Koganei DTY-EPS Series, Manual

Page: 7 / 16

y
Connect the EP Sensor DTY-EPS and the mini clamp connector. Follow
the procedure below to perform the connections.
1. Check that the connector cover (the part where lead wire is inserted)
is protruding from the connector body.
It cannot be used if it’s flat and placed at the same level against the
body.
2. Arrange the EP Sensor cable into the required form.
Since the insulation on the tip of the lead wire has been peeled off
and soldered, cut the wires at about 10mm [0.39in.] from the tip so
that it does not protrude from the insulation.
3. Follow the instructions in the table to insert the lead wires into the
hole in the connector cover. Look through the top of the semi-
transparent cover to check that the lead wires have been firmly
inserted all the way to the back. (Insertion is about 9mm [0.35in.].)
Use caution in making the connections, since switching on the power
with mistakes in the connections will damage the EP Sensor and EP
Monitor.
4. Taking care to avoid letting the lead wire slip out from the connector,
use pliers or some other hand tool to crimp the cover and connector
body, and push the cover into the connector body.
Limit the crimping force to 980.7N [220lbf.] or less.
When the cover is flat and placed at the same level against the
connector body, the connection is complete.
5. Check one more time that the wiring is correct.
Sensor and connector connection procedure
To mount the EP Sensor and the power supply, switch, and
communication cable, align the lock lever position as shown in the figure,
and push until the lock hooks on the controller-side connector.
To remove, push down hard on the lock lever, take the connector and pull
it out. At this time, be careful to avoid applying unnecessary force on the
lead wires.
Connector for
4 EP Sensors
Connector for power
supply, switch, and
communication cable
1ch
DTY-EPP-
□
-
□
DTY-EPS
2ch
3ch
4ch
Power supply, switch,
and communication cable
EP Sensor
Lock lever
Lock lever
4 3 2 1
Attaching and removing of the EP Sensor, and the
power supply, switch, and communication cable
Attaching the panel mounting parts and protective front cover
Use the hex socket head
screws (M2.6
× 0.45,
length 5mm [0.197in.]) to
mount the mounting
bracket into the mounting
holes on the back of the
sensor controller.
The tightening torque
should be 0.32N
･
m
[2.83in ･ lbf].
2-M2.6 × 0.45
Depth 6 [0.236in.]
(Mounting thread)
Mounting bracket
PSU-BR
Hex socket
head screw
(Provided with
mounting bracket)
Attaching the mounting bracket
Panel plate
Mounting
body
Protective
front cover
(sold separately)
EP Monitor
Mounting holder
Groove on panel mounting body
1)
2)
3) 4)
Mounting and wiring
Cut
Ground terminal
Caution
No. on the connector
1
2
3
4
Color of lead wire
EP Sensor yellow/red wire
EP Sensor white/red wire
EP Sensor yellow/black wire
EP Sensor gray/red wire
EP Sensor
Yellow/red wire
White/red wire
Yellow/black wire
Gray/red wire
1) Insert the mounting
body from the front of
the panel hole.
2) Insert the sensor
controller from the
back of the mounting
body.
3) From the back of the
position in 2), place
the mounting holder
on the mounting body
groove, and insert it.
4) Set the separately
sold protective front
cover in place.
※
For removal, follow the above
procedure in reverse, using a
screwdriver or other tool to remove
the mounting holder.
Signal name
EP Sensor power supply ( ＋ )
EP Sensor analog output
EP Sensor power supply (0V)
EP Sensor abnormality
EP Sensor
1 2 3 4
Caution: Prepare any unused lead wires so that they will not short circuit.