Kodiak CKC3200GPC Owner'S Manual Download Page 4

3

Safety Precautions 

– continued

 22.  DO NOT allow your pressure washer to freeze
 

  during colder months. Damage as a result of

 

  freezing will void the warranty.

 23.  Prior to starting the pressure washer in cold
 

  weather, be sure that ice has not formed in

 

  any part of the equipment.

 24.  Never tie knots or kink the high-pressure hose
 

  as damage could result. DO NOT operate the

 

  unit if the high-pressure hose is damaged.

 25.  The Gun Safety Lock PREVENTS the trigger
 

  from accidentally being engaged. This safety

 

  feature DOES NOT lock trigger in the ON

  

position.

26.   Securely connect the discharge lines before 
 

  starting the pump. An insecurely connected

 

  line may whip, causing personal injury and/or

  

property 

damage. 

27.   To avoid serious injury and damage to the unit
 

  DO NOT operate this pressure washer with

 

  any components rated less than the pressure

 

  rated for each model (i.e.: spray guns, hoses, 

 

  hose couplings, etc...)

 28. DO NOT allow the pressure washer to run for
 

  more than 3 minutes with the gun closed and

 

  the engine running. Prolonged operation in

 

  bypass mode can result in damage to the pump.

 29.  Shut the engine OFF if you are not using the
  

pressure 

washer.

 CAUTION: 

The pressure has been preset by

  the manufacturer. DO NOT attempt to adjust the
  pressure higher than its factory setting. Doing so
  will damage the pump, void the warranty and
  could result in personal injury or damage.

 CAUTION: 

This machine has been designed

  for use with pressure washer detergents only.

Important Safety Precautions 

– continued

 

Water Supply 

(Cold Water Only)

This pressure washer must only be used with
clean water; use of unfiltered water or corrosive
chemicals will damage the pressure washer.

 1.  The supply hose should be at least 5/8"
  

in 

diameter

 2. The water supply must be at least twice to
   the flow rate of the pressure washer. (GPM)
 3. The water supply pressure must be a minimum
   of 20 psi and must not exceed 120 psi.
 4. The water supply temperature must not exceed
  

40˚C/104˚F.

 5. Never use the pressure washer to draw in
   water contaminated with solvents, e.g. paint
   thinners, gasoline, oil, etc.
 6. Always prevent debris from being drawn into
   the unit by using a clean water source.
 7. Calcium build-up due to hard water is NOT
   covered by the warranty.

Important Safety Precautions 

– continued

Summary of Contents for CKC3200GPC
















Reviews: