Kodak DryView 6800 Diagnostics Manual Download Page 181

Page: 181 / 326

DIAGNOSTICS

Status Messages and Error Codes

30JUL07

8F2919

Page

181 of 326

FE Action

Do the actions below in sequence. If an action provides a resolution, do not continue with the
other actions.

De-energize then energize the LASER IMAGER.

Do the following:

Install a new TURNAROUND AY. See the ADJUSTMENTS AND REPLACEMENTS,

TURNAROUND AY - IMAGER with SORTER

Check:

If an existing problem:

For film jam in area 5

Remove films.

FILM CARTRIDGE

Install a new FILM CARTRIDGE.

BELTS

Install new BELTS.

DENSITOMETER FILM
DETECT SENSOR - use the
SERVICE TOOL

Install a new TURNAROUND AY. See the
ADJUSTMENTS AND REPLACEMENTS,

TURNAROUND AY - IMAGER with SORTER

Summary of Contents for DryView 6800







































































































































































































































































































































Search results

Summary of Contents for DryView 6800

Reviews:

Brands by name

Popular brands

Kodak DryView 6800, Diagnostics Manual

Search results

Summary of Contents for DryView 6800

Reviews:

Brands by name

Popular brands