Kodak DryView 6800 Diagnostics Manual Download Page 130

Page: 130 / 326

DIAGNOSTICS

Status Messages and Error Codes

30JUL07

8F2919

Page

130 of 326

FE Action

Do the actions below in sequence. If an action provides a resolution, do not continue with the
other actions.

De-energize then energize the LASER IMAGER.

Check the mechanical operation:

•

Do the following:

Check:

If an existing problem:

FILM CARTRIDGE

Install a new FILM CARTRIDGE.

CONNECTORS and CABLES Seat all CONNECTORS.

BLINDMATE CONNECTOR

Adjust THE BLINDMATE. See the ADJUSTMENTS AND
REPLACEMENTS,

BLINDMATE BRACKET

FILM OUT SENSOR - use the
SERVICE TOOL

Install a new SENSOR. See the ADJUSTMENTS AND
REPLACEMENTS,

SENSOR, FILM OUT (S3) - PICKUP

CUPS ENGAGED SENSOR -
use the SERVICE TOOL

Install a new SENSOR. See the ADJUSTMENTS AND
REPLACEMENTS,

SENSOR, CUPS ENGAGED (S2)

and PICKUP HOME (S1) - PICKUP AY

ROLLER DRIVE MOTOR

Install a new MOTOR. See the ADJUSTMENTS AND
REPLACEMENTS,

MOTOR, FEED ROLLER DRIVE

(M2) - PICKUP AY

ROLLER DRIVE MOTOR
BELT

Install a new BELTS. See the ADJUSTMENTS AND
REPLACEMENTS,

BELTS, ROLLER DRIVE and

ROLLER OPEN/CLOSE - PICKUP AY

PICKUP DRIVE MOTOR

Install a new MOTOR. See the ADJUSTMENTS AND
REPLACEMENTS,

MOTOR, DRIVE (M3) - PICKUP AY

TENSION SPRINGS

Install a new SPRING.

Summary of Contents for DryView 6800







































































































































































































































































































































Search results

Summary of Contents for DryView 6800

Reviews:

Brands by name

Popular brands

Kodak DryView 6800, Diagnostics Manual

Search results

Summary of Contents for DryView 6800

Reviews:

Brands by name

Popular brands