background image

Heinrichs Messtechnik 

TSK1 Installation and Operating Instructions 

 

Page 4 of 27  

 

Introduction 

 
These Installation and Operating Instructions serve as a tool 
for the correct installation, operation and maintenance of the 
device.  They are a supplement to the TSK Device 
Description.  Read the manual carefully before the device is 
installed and put into use.  It does not include special 
versions or applications. 
 
All devices are thoroughly checked for order compliance and 
operability before delivery.  Upon receipt, please conduct a 
visual inspection of possible damage that may be identified 
as having occurred during shipment.  If you discover any 
defect, please contact our head office in Cologne or the local 
sales office responsible for your area (see the telephone 
directory at the end of this manual or on our Web site).  
Apart from a description of the error, we will need the 
equipment type and serial number of the delivery.  
 
Heinrichs Messtechnik shall not furnish guarantee for any 
repair work done without prior notice.  Unless otherwise 
agreed on, the rejected parts must be made available to us 
in case a claim is made. 
 

Identification 

1.1 

Supplier/manufacturer 

Heinrichs Messtechnik GmbH 
Robert-Perthel-Str. 9   D-50739 Köln 
Phone  +49 (221) 49708 - 0 
Fax      +49 (221) 49708 - 178 
Internet: 

http://www.heinrichs.eu/

 

E-mail

mailto:[email protected]

 

1.2 

Product type 

Paddle-type flowmeter in all-metal design  

1.3 

Product name 

TSK1 with subgroups 
TSK1-C (stainless steel) 
TSK1-S (stainless steel) 
TSK1-K (polypropylene/stainless steel) 
TSK1-P (PTFE/Hastelloy C) 

1.4 

Issue date  

20/10/2008 

1.5 

Version no. 

3.0 
File: TSK1_BA_03_eng 
 

Applications 

The TSK meter is suitable for flow measurement of liquid 
products in pipes.  

The special advantage is that it can be 

used for all directions of flow.  

It shows the current flow 

rate in volume or mass per unit in time. 
 
Applications:  flow measurement, dosing, monitoring, 
adjusting and control of liquid and gaseous products. 
The meter’s design makes it ideal for processes under 
difficult and adverse operating conditions. 
 
The devices are available with additional electrical 
equipment for process monitoring and control. 
 

Operational mode and system design  

3.1 

Measuring principle 

If a medium flows with sufficient velocity through the 
horizontally or vertically arranged measuring chamber (1) if 
the TSK fitting, the paddle (2) will swivel around the axle until 
the force of the medium and the opposing force of the 
paddle surface plus the spring tension establish equilibrium.    
The angular position or the position of equilibrium ( ) of the  
paddle (2) in the measuring chamber (1) is the measure for 
the flow. The encapsulated ring-type permanent magnet (4) 
at the end of the paddle axis (3) then transmits this position 
to the scale (6) and the optional electronic evaluators 
through the magnet tracking indicator (5) system. This 
happens safely and without packing glands.    
The flow rates shown on the scale only apply to the 
calibrated medium or to a medium with the same physical 
characteristics. 

3.2 

System design 

The TSK flowmeter mainly consists of the fitting with the 
measuri

ng chamber, the measuring elements “torsion spring” 

and “paddle,” the magnet tracking indicator system and the 
indicator unit.  
The flowmeter is manufactured as a sandwich-type 
construction and available for the nominal sizes from DN 50 
to DN 400. 
 

 

 

Fitting 

Paddle 

Paddle axis with torsion spring 

Ring-type permanent magnet 

Magnet tracking indicator system 

Scale 

Cover with window 

Base plate of indicator housing 

Coupling chamber 

Input 

4.1 

Measured variable 

 
Volume flow 

4.2 

Measuring range (lower-range and upper-
range value) 

Measuring range span 

15

–100% 

Smallest measuring range 

1.5

–10 m3/h water 

Largest measuring range 

185

–1300 m3/h water 

Electrical signal outputs  

20

–100% 

 

Summary of Contents for Heinrichs TSK




























Reviews: