manualshive.com logo in svg

Ko Propo EX-RR, Instruction Manual

Share
Download
Ko Propo EX-RR Instruction Manual Download Page 40

40

67((5,1*

)((/

'<1$0&

75,0

63(('

5(9(56

75$9(/

L 70％

N

R70%

ST  TRAVEL：

100

ST TRAVEL トラベル

/٫

1

5

6775$9(/؟

6775$9(/

STEERING

TRAVEL menu

Modify the overall amount of steering movement.

▶ ST TRAVEL　
　

Modify the overall amount of steering movement.

▶ L（BALANCE）　
　

Modify the left steering angle end point.

▶ R（BALANCE）　
　

Modify the right steering angle end point.

Adjust the overall amount of steering servo movement
when the steering wheel is at full lock.

▶ ST TRAVEL  Steering Travel

Since the Balance setting value is a ratio of the
Travel setting value, if the latter is modified the actual
movement value and the displayed graphic will also
change.(the Travel value will not change).

P

Steering will not operate if the Travel value is set to 0.

Adjust the left/right steering angles independently.
This enables the turning radii to match up during
cornering.

【Setting Range】

ST TRAVEL : 0 〜 150（Default: 100）

【Setting Range】

ST BALANCE L : 30 〜 100（Default: 70）
ST BALANCE R : 30 〜 100（Default: 70）

▶ ST BALANCE L R　Steering Balance L R

The set percentage is a ratio of the value set by the
Steering Travel.

P

If the trim is set to a large value, a large left/right value
discrepancy may result. If adjusting steering balance for
the first time, follow the procedures below.
① Set trim value to 0.
② Adjust sub trim so that the car drives in a straight line
　 when steering is in neutral position.
③ Use steering travel to match the overall steering
　 angle range.
④ Use steering balance to match the left/right turning
　 radii.
⑤ If the car does not drive straight at this point, use trim
　to correct.

P

Steering balance can be adjusted by using

the steering wheel and ET key!

ET key that is assigned to steering trim is pressed
while the steering is turned over halfway in either
direction, the balance of the direction of the turn can be
adjusted.

P

Summary of Contents for EX-RR


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands