33
3・4CH menu
->KEY:OFF
TRIM 0
BRAKE 100
TH HOLD 0
HIPOINT 100
REVERSE NORM
MODE
NORMAL
->KEY:OFF
->KEY:OFF >>>
->KEY:OFF
->KEY:OFF
3CH MODE ： AMP
ET MODE SET
3CH MODE:AMP
NORMAL :
BURN ：ON
DIG ：ON
＜＜＜
F HOLD：ON
ON
R HOLD：ON
▶ AMP Mixing MODE
Used when the front and rear wheels are controlled
by separate ESCs and motors. If 3CH or 4CH is set
to the front-wheel drive function, it will operate in
conjunction with 2CH's throttle operations.
【Setting Range】
MODE （Default: NORMAL）
NORMAL : drives both front and rear wheels
BURN : drives rear wheels only
DIG : drives front wheels only
F HOLD : drives front wheels at a set speed
R HOLD : drives rear wheels at a set speed
TH HOLD : -100 〜 100（Default: 0）
This function adjusts the set speed used for (F HOLD)
and (R HOLD) selected in Amp Mixing Mode. [F HOLD]
adjusts the front wheel drive while [R HOLD] adjusts the
rear wheel drive.
※ This setting is activated when F HOLD or R HOLD
mode is selected.
HIPOINT : 0 〜 150（Default: 100）
Adjusts the maximum amount of throttle to be applied
to the front wheels. Equivalent to the [Throttle High Point]
function.
※ This setting is activated when NORMAL, DIG, or R
HOLD mode is selected.
TRIM : -50 〜 50（Default: 0）
Adjusts the neutral position of the front wheels.
REVERSE : NORM、REVS（Default: NORM)
Changes the movement direction of the front wheels.
MODE → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET or BT keys to activate the various front
wheel drive modes.
TH HOLD → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET keys to be used for the set speed used
for TH HOLD.
HIPOINT → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET or BT keys to adjust HIPOINT value.
BRAKE → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET or BT keys to adjust BRAKE value.
REVERSE → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET or BT keys to changes the movement
direction of the front wheels.
BRAKE : 0 〜 150（Default: 100）
Modify the maximum amount of reverse (brake) to be
applied to the front wheels. Equivalent to [Throttle Brake]
function.
※ This setting is activated when NORMAL, DIG, or R
HOLD mode is selected.
【Setting Range】
ET MODE SET
Assigns ET or BT keys to activate the various front
wheel drive modes.
NORMAL : ON、OFF（Default: ON）
BURN : ON、OFF（Default: ON）
DIG : ON、OFF（Default: ON）
F HOLD : ON、OFF（Default: ON）
R HOLD : ON、OFF（Default: ON）
This makes it easy to adjust the amount of maximum
throttle, particularly on a glow engine car.
The setting position cannot exceed what is set by [High
Point] or [Brake].
Assigning these keys may be convenient for rock
crawlers or when you need to adjust Amp Mixing
settings.
For electric cars, the throttle is set by the ESC so there
is no need to set this function. However, some older
ESCs will not function properly unless reverse is also
set.
P
P
P
P
If the amp mixing high point is set low and the amp
mixing trim is set to a high value toward acceleration,
the resulting throttle movement may be extraordinarily
small.
P
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On electric cars, a setting value that is too small
may cause problems with the ESC settings. Make
adjustments starting from the default setting (100).
On electric cars, a setting value that is too small
may cause problems with the ESC settings. Make
adjustments starting from the default setting (100).
Brake will not operate if the value is set to 0.
Brake will not operate if the value is set to 0.
【Example】
May be used for rock crawlers, etc.
