2
SAFETY INSTRUCTIONS
ADDITIONAL SAFETY RULES FOR TOOL
SAVE THESE INSTRUCTIONS
1. Wear dye protection
2. Do not use the tool in presence of flammable liquids
or gases
3. Always use face or dust mask.
4. Check the blade carefully for cracks or damage before
operation. Replace cracked or damaged blade
immediately.
5. Use only saw blades recommended by the manufacturer
and which conform to the stand of your country.
6. Always use accessories recommended in this manual.
Use of improper accessories such as abrasive cut-off
wheels may cause in injury.
7. Select the correct saw blade for the material to be cut.
8. Do not use saw blades manufactured from high
speed steel.
9. To reduce the emitted noise, always be sure that
the blade is sharp and clean.
10. Do not cut metals such as nails and screws. Inspect
for and remove all nails, screws and other foreign
matter form the workpiece before operation.
11. Remove wrenches, cut-off pieces, etc, from
the table before the switch is turned on.
12. Keep hands out of the line of the saw blade.
13. Never stand or permit anyone else to stand in line
with the path of the saw blade.
14. Before using the tool on an actual workpiece, let it run
for a while. Watch for vibration or wobbling that could
indicate poor installation or a poorly balanced blade.
15. Replace the table insert when worn.
16. Connect band saw to a dust-collecting device when
sawing wood.
17. Do not operate the machine when the door or guard
protecting the saw band is open.
18. Take care that the selection of the saw band and
the speed depends on the material to be cut.
19. Do not clean the saw band whilst it is in motion.
ELECTRICAL REQUIREMENTS
To avoid electrical hazards, fire hazards,
or damage to the tool, use proper circuit protection.
Use a separate electrical circuit for your tools. To avoid shock
or fire, if power cord is worn or cut, or damaged in any way,
have it replaced immediately.
POWER SUPPLY AND MOTOR SPECIFICATIONS
WARNING
GROUNDING INSTRUCTIONS
WARNING
This tool must be grounded while in use
to protect the operator from electrical shock.
3-prong
plug
Grounding
prong
Properly
ground
outlet
Grounding lug
Adapter
Make sure this is connected
to a known ground
Pronged
receptacle
Improper connection
of equipment grounding
conductor can result in
the risk of electrical shock.
equipment should be
grounded while in use
to protect operator from
electrical shock.
WARNING
This machine is for indoor use only.
Do not expose to rain or use in damp locations.
WARNING
- Check with a qualified
electrician if you do not
understand grounding
instructions or if you
are in doubt as to whether
the tool is properly grounded.
- This tool is equipped with an approved cord and a 3-prong
grounding type plug for you protection against shock
hazards.
- Grounding plug should be plugged directly into a properly
installed and grounded 3-prong grounding-type
receptacle, as shown.
- Do not remove or alter grounding prong in any manner.
in the event of a malfunction or breakdown, grounding
provides a path of least resistance for electrical shock.
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This tool is
equipped with an electric cord that has an equipment-grounding
conductor and a grounding plug. The plug MUST be plugged
into a matching receptacle that is properly installed and
grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit
the receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment-grounding
conductor can result in risk of electric shock. The conductor
with green insulation (with or without yellow stripes) is
the equipment-grounding conductor. If repair or replacement
of the electric cord or plug is necessary, DO NOT connect
the equipment-grounding conductor
to a live terminal.
CHECK with a qualified
electrician or service person
if you do not completely
understand the grounding
instructions, or if you are not
sure the tool is properly
grounded.
Refer to nether picture:
USE PROPER EXTENSION CORD. Make sure your extension
cord is in good condition. When using an extension cord,
Be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in
line voltage, resulting in loss of power and cause overheating.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or have
it repaired by a qualified person before using it. Protect your
extension cords from sharp objects, excessive heat and damp
or wet areas.
GUIDELINES FOR EXTENSION CORDS
