background image

3

TECHNICAL DESCRIPTION

Connection

   • The welder should be placed in dry and dusty

      surrounding where there is no corrosive chemicals,

      flammable, explosive gases.
   • Avoid direct sunlight and rain. And maintain the ambient 

      temperature ranging from -10º C to 40º C.
   • The space of 50 cm should be left around the equipment.
   • If indoor ventilation is not good enough, the ventilation

      exhaust device should be installed.

Power Source Connection

Access the back panel (power source cable) to the power

supply which is equipped with circuit breakers and grounding

line (grid), and it is strictly prohibited that ground wire is

connected to the grid, otherwise bear your own

consequences.

Electrode Polarity (see above picture)

Connect the quick plug with electrode holder to the positive

terminal and then tightened them up clockwise.

Workpiece Connection

Connect the quick plug with earth clamp to the negative

terminal on the front panel below. And then tighten them up. 

Access the earth clamp to the workpiece.

Welding torch

Work piece

Grounding cable

Installation Diagram

                    It is forbidden to connect

the workpiece to the welder with iron

or other poor conductors. 

WARNING

A

V

3

Fuse

Amperage

Voltage

Thee phase

1

X

Positive earth

Line

Single phase

Duty cycle

SMAW

GTAW

Wire feed

function

High

Temperature

Welding gun

GMAW

INSTALLATION

Summary of Contents for KN INW-160

















Reviews: