background image

 

 

 

FCC Warning 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.  

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Canada 

This Class B digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  

 

Caution:

 To reduce the risk of electrical shock, do not remove the cover (or back). 

No user serviceable parts inside. Refer to qualified service personnel.  
 

Warning:

 To reduce the risk of fire or electric shock, do not expose this appliance to 

rain or moisture.  

 
The lightning flash with arrowhead, within an equilateral triangle, is 
intended to alert the user to the presence of uninsulated “dangerous 
voltage” within the products that may be of sufficient magnitude to 

constitute a risk of electrical shock to persons. 

 

The exclamation point within an equilateral triangle is intended to alert 
the user to the presence of important operation maintenance (servicing) 
instructions in the literature accompanying the appliance. 

 

 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

Summary of Contents for GSZ67

















Reviews: