background image

12 

Each keypad must be programmed individually and it will save the label names even if the 
keypad is disconnected from the systems. The MR164 keypad labels can be programmed offsite 
if desired.  
 

         Note:

  All of the MR164 keypads in this system have to be programmed  

       with the same labels and in the same source order. 
 

 
The sources should be connected, but it is not necessary to have the source wires connected to 
program the keypad labels.  
 
Using the back of this manual, please write down the source name connected to source 1, source 
2, source 3, source 4, source 5, source 6 and source 7. 
 
With the amplifier turned on and the zone identification completed (above), the source input 
labels are now ready to be programmed. This is how the source that has been selected, and is 
playing, is easily identified on the keypad LCD readout. 
 
First the system must be powered up, but all zones turned off. The keypad will display:    
 
                                                                   
 

 

                                            System Off 

 
 
To enter the installer menu from “System Off” press the keypad 

MUTE

 button for about 1 second 

then immediately press the 

INPUT

 for about 5 seconds. Release the 

INPUT

 button as soon as 

the LCD displays: 

 
                                              
                                           Source 1 

 
 
Now press the 

UP

 or 

DOWN

 buttons next to the 

INPUT

 buttons to scroll through the label 

selections for source A on the bottom row of the LCD display. When the correct selection is 
displayed press the 

INPUT

 button to confirm this choice.  

 
 

      Note: 

If a mistake is made, go though the rest of the programming  

                setup, and restart the installer mode again. 
 
 
The LCD display then displays: 

                                               
                                            Source 2 

 
 
Press the 

UP

 or 

DOWN

 buttons next to the 

INPUT

 buttons again to scroll through the label 

selections for source 2 on the bottom row of the LCD display. When the correct selection is 
displayed press the 

INPUT

 button to confirm this choice. 

 
Continue programming for sources 3, 4, 5, 6 and 7 in the same manner.   The keypad labels have 
been set. To change any of the labels you can re-enter the installer menu and scroll through all 
seven labels and reset the ones needed. 
 
 

3. Equalization (if required).

 The LCD display then displays 

 

      BASS 

Summary of Contents for GSZ67

















Reviews: