background image

GENEral

3

Status: 13.10.21

1  General

1.1  Notes on operating instructions

These operating instructions are designed to enable you to use your tool 

safely and efficiently.

The tool may only be used if it is in technically perfect condition.
As a consequence of technical developments, the illustrations and descrip-
tions contained in these operating instructions may differ slightly from the 
tool actually delivered.
We do not accept any liability for damage caused by failure to observe these 
operating instructions.

1.2  Symbols used

All safety instructions in these operating instructions are indicated by corre-
sponding symbols. The signal words at the beginning of each safety instruc-
tion express the extent of the Hazard.

Danger!

Level 1 risk source

This combination of symbol and signal word indicates an imminently haz-
ardous situation that will result in death or serious injury if not avoided.

Warning!

Level 2 risk source

This combination of symbol and signal word indicates a possibly hazardous 
situation that may result in death or serious injury if not avoided.

Caution!

Level 3 risk source

This combination of symbol and signal word stands for important informa-
tion that will assist in preventing damage to property or the environment.

1.3  Copyright

These operating instructions and all documentation supplied with this tool 
are protected by copyright and remain the property of KNIPEX.
The reprinting of these instructions, even in extract form, is only permitted 
with the written consent of C. Gustav Putsch KG.

1.4  Guarantee and warranty

The manufacturer grants a statutory warranty in accordance with the cur-
rent sales and delivery conditions. No further warranties or assurances are 
granted.

Summary of Contents for 902210BK













Reviews: