background image

0901220 Rev: A (final 04/20)

 

Page 12 of 12

 

DISCLAIMER

 

Knight LLC does not accept responsibility for the mishandling, misuse, or non

-

performance of the described items when used 

for purposes other than those specified in the instructions. For hazardous materials information consult label, MSDS, or Knight 

LLC. Knight products are not for use in potentially explosive environments. Any use of our equipment in such an environment 

is at the risk of the user, Knight does not accept any liability in such circumstances.

 

WARRANTY

 

All Knight controls and pump systems are warranted against defects in material and workmanship for a period of ONE year. All 

electronic control boards have a TWO year warranty. Warranty applies only to the replacement or repair of such parts when 

returned to factory with a Knight Return Authorization (KRA) number, freight prepaid, and found to be defective upon factory 

authorized inspection. Bearings and pump seals or rubber and synthetic rubber parts such as 

O

” 

rings, diaphragms, squeeze 

tubing, and gaskets are considered expendable and are not covered under warranty. Warranty does not cover liability resulting 

from performance of this equipment nor the labor to replace this equipment. Product abuse or misuse voids warranty.

 

FOOTNOTE

 

The information and specifications included in this publication were in effect at the time of approval for printing. Knight LLC 

reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring 

any obligation whatsoever.

 

Knight Headquarters

 

Tel: 949.595.4800

 

Fax: 949.595.4801

 

USA Toll Free

 

Tel: 800.854.3764

 

Knight Canada

 

Tel: 905.542.2333

 

Fax: 905.542.1536

 

KNIGHT LLC

  (www.knightequip.com)

 

Summary of Contents for Idex MX PLUS













Reviews: