manualshive.com logo in svg

Knick Portavo 908 MULTI, User Manual

Share
Download
Knick Portavo 908 MULTI User Manual Download Page 5

5

Table of Contents

Oxygen Calibration ................................................................................................ 34

Calibration in Air ........................................................................................................................................... 34
Zero Calibration ............................................................................................................................................ 35
Data Entry Calibration ................................................................................................................................ 35

Measuring ............................................................................................................... 36

Toggling the Measured Value Display .................................................................................................. 36
Adjusting the Temperature ....................................................................................................................... 36

Printing .................................................................................................................... 37

Printing Currently Measured Values ...................................................................................................... 37
Printing a Calibration Record ................................................................................................................... 38

Data Logger ............................................................................................................ 39

Operating Modes of the Data Logger (Logger Type) ...................................................................... 40
Configuring the Data Logger ................................................................................................................... 42
Increasing the Battery Life ........................................................................................................................ 42
Starting/Stopping the Data Logger ....................................................................................................... 44
Viewing the Logger Data ........................................................................................................................... 44
Deleting the Logger Data .......................................................................................................................... 44

Paraly SW 112 Software ......................................................................................... 46
Error and Status Messages ..................................................................................... 47

“Sensoface” Messages ................................................................................................................................. 48
Info and Help Texts ...................................................................................................................................... 48
Error Messages .............................................................................................................................................. 49

Option 001 SOP ...................................................................................................... 50
Option 002 Temp.Cal .............................................................................................. 50
How to Enter the Rescue PIN Code ........................................................................ 54
pH Product Line ...................................................................................................... 56

pH Sensors ...................................................................................................................................................... 56
Knick CaliMat (pH) Buffer Solutions ....................................................................................................... 57
Accessories for pH, ORP ............................................................................................................................. 57

Conductivity Product Line ..................................................................................... 58

Conductivity Sensors .................................................................................................................................. 58
Conductivity Standards.............................................................................................................................. 59
Accessories for Conductivity .................................................................................................................... 59

Oxygen Product Line .............................................................................................. 60

Oxygen Sensors ............................................................................................................................................ 60
Accessories for Oxygen .............................................................................................................................. 60

Specifications .......................................................................................................... 61
Index ........................................................................................................................ 67

Summary of Contents for Portavo 908 MULTI













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands