Knick Portavo 904 User Manual Download Page 42

Page: 42 / 54

TAN Options

Order No.

SOP (Standard Operating Procedure): user management, sensor
verification, temperature detector adjustment in the Memosens
sensor (offset correction)

SW-P001

Temperature detector adjustment in the Memosens sensor
(offset correction)

SW-P002

Paraly SW112 PC software for configuration and firmware updates:
Free download from www.knick.de

Conductivity Sensors

Please visit our website for more information on our product range: www.knick.de.

Conductivity Standards

for determining a cell constant
Ready-to-Use Solutions

Quantity

Order No.

1.3 µS/cm, KCl

300 ml

ZU0701

15 µS/cm, KCl

500 ml

CS-C15K/500

147 µS/cm, (0.001 mol/l KCl)

500 ml

CS-C147K/500

1413 µS/cm, (0.01 mol/l KCl)

500 ml

CS-C1413K/500

12.88 mS/cm, (0.1 mol/l KCl)

500 ml

CS-C12880K/500

Solutions for Preparation

For preparation of 1000 ml 0.1 mol/l
NaCl solution (12.88 mS/cm)

1 ampoule

ZU 6945

Product Line

Summary of Contents for Portavo 904























































Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands

Knick Portavo 904, User Manual

Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands