manualshive.com logo in svg

KNECHT S 200 BS, Operating Instructions Manual

Share
Download
KNECHT S 200 BS Operating Instructions Manual Download Page 38

39

7. Operation 

Figure 7-17

 Changing the finned brush

7.14  Changing the finned brush

To change the finned brush, loosen the cap nuts 
(7-16/1) counter-clockwise using the flat wrench 
(SW 17) provided. 

Remove the polishing protection hood and clean it 
under running water.

Open the clamping nut (7-17/1) counter-clockwise 
using the flat wrench (SW 22) provided. Pull the 
used finned brush from the grinding spindle and 
replace it with a new one.

Then mount the complete guard again in reverse 
order.

Verify that all parts are functioning properly! 

ATTENTION

Only original finned brushes approved by 
Knecht Maschinenbau GmbH may be used.

Incorrect finned brushes can cause cutting 
tools to be deburred insufficiently and 
 damage the cutting edges.

 

Do not switch on the machine with the protection hood removed!

Serious injury may result!

CAUTION

Figure 7-16

 Loosening the cap nuts

1

1

1

Summary of Contents for S 200 BS















































Reviews:

No comments

Brands by name

Popular brands

Load more brands