background image

12 

LUBRICATION 

 

It  is  very  important  to  maintain  the  proper  oil  level  in  the  pump  crankcase.    The  oil  level  is 

checked via the site glass located on the top of the pump.  The pump requires a SAE 30W                non
-detergent oil. 

 

 

The  pump  crankcase  oil  should  be  changed  after  every  500  hours  of  use  or  when  the  pump    

diaphragms are replaced.  The oil is changed as follows: 

1)  Drain the oil from the pump by removing the cap from the oil site glass, removing the pump mount 

bolts and loosen the necessary hoses. Turn the pump upside down and rotate the crankshaft until oil 
stops flowing out. 

2)  It is recommended that the  inside of the pump crankcase be washed with gasoline or diesel oil. 
3)  Using  a  SAE  30W  non-detergent  oil,  refill  the  pump  through  the  site  glass  to  the  proper  level.      

Rotate the crankshaft while filling to distribute the oil. 

4)  Before putting the cap back on the oil site glass, run the pump with no pressure (raise the control 

unit pressure release lever) until all air bubbles are vented. 

5)  After  replacing  the  cap  on  the  oil  site  glass,  check  the  oil  level  with  the  pump  operating  with      

pressure. 

 

The PTO driveline should be greased as follows:  Grease the universal joints and shield fitting 

after every 8 hours of use.  Grease the locking collars and driveline tubes after every 20 hours of use. 

TRANSPORTATION 

 

Before  towing  the  washer/sprayer  for  extended  distances,  make  the  following  preparations:   

Remove the PTO driveline, detaching it from the pump.  Secure the spray gun in the holster.  Secure 
the break-away boom with a rope, rubber strap, etc. to prevent it from opening when crossing rough 
areas such as railroad crossings.  Maximum towing speed is 25 MPH. 

STORAGE 

 

The Poultry House Washer/Sprayer should be washed down thoroughly.  After washing, treat-

ing with a disinfectant is recommended to kill any remaining bacteria.  Treat the metal components of 
the machine with a soluble oil to protect from rust and corrosion.  One product which meets these re-
quirements is called “Film Fluid” manufactured by Eureka Chemical Co., San Francisco, CA.  It is sold 
in some tractor dealerships and farm supply dealers. 
 

If the pump will experience freezing conditions, empty the pump of water completely.  An extra 

precautionary measure is to flush the pump with a 50/50 anti-freeze and water mixture. 

Summary of Contents for 44 Series





















Reviews: