klover DEA ECO 12 Manual Download Page 4

 

 

EN

G

LISH

 

INTRODUCTION 

Important security instructions

 

Read the following instructions prior to installing and using the product. 

 

 

 

Stove installation and initial start-up must be performed by expert personnel conscious of the 

importance of observing the applicable safety standards. Said personnel shall be responsible for 

the definitive installation of the device and its proper operation thereof.

 

KLOVER srl shall not be held liable if these precautions are not observed.

 

During installation of the device, all local regulations - included those referring to national and 

European Standards - must be observed.

 

  Connect the flue gas outlet to a flue having the features described in the 

Connections 

section of this 

User 

Guide.

 

  The device is not suitable for installation on a shared flue system. 

  If the flue should catch fire, employ appropriate systems for extinguishing the flames or call the fire 

brigade. 

  Connect the product to earthed sockets. Avoid using sockets controlled by switches or automatic timers. 

  Do not use a damaged or worn power supply cable. 

  If a multiple socket is used, make sure that the total voltage of the connected devices does not exceed 

the voltage supported by the socket. Furthermore, make sure that the total voltage of all devices 

connected to the socket does not exceed the maximum allowed level. 

  Do not use easily flammable substances to clean the device or its elements. 

  Do not leave flammable containers and substances in the room where the stove is installed. 

Do not use the device as an incinerator or for any use other than that for which it was designed.

  Do not use different fuels to those recommended. 

  Do not use liquid fuels. 

  The device - especially its external surfaces - becomes very hot to the touch during operation; handle it 

with caution in order to avoid burns. 

  Only use original spare parts recommended by the manufacturer. 

  Do not perform any unauthorised modification on the device. 

 

Using poor-quality pellets or pellets made of any other material may damage the stove's 

functions, besides voiding the warranty and the manufacturer's liability. 

  The Klover pellet products are not suitable for use  in smokeless zones.

  

 

A few precautions

 

  Do not touch any 

hot parts

 of the product (ceramic glass, flue pipe) during normal operation.

 

  Use the appropriate button to switch the electrical panel off. Do not disconnect the power supply cable 

while the stove is operating.

 

  Keep children away from the stove during normal operation, as they may suffer burns if they touch the 

stove's 

hot parts

 

  Children and inexperienced people must not be allowed to use the device.

 

 

NEVER open the door of the stove during normal operation.

 

 

 

Intended use

 

The automatic operation 

DEA ECO

 stove by Klover is designed for heating your entire home. 

The stove works exclusively with wood pellets and only with the hearth door shut. Never open the 

door while the device is operating. 

The stove comes with a DOUBLE COMBUSTION system guaranteeing “clean” flue gas emissions with 

among the lowest CO

2

 values in Europe, alongside excellent mean performance values. 

 

Do not use the stove in ways other than those indicated in this user guide. The stove is designed for 

indoor use only. 

 

This user guide constitutes an integral part of the stove. 

If the product is sold to another user, this manual must be handed down to the new owner. 

Summary of Contents for DEA ECO 12


































Reviews: