background image

Tech Support:  

1-800-KLIPSCH

23

THIS DEVICE COMPLIES WITH FCC RULES PART 15.

Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) This device must accept any interference received including that may 
      cause undesired operation.

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
   -- Reorient or relocate the receiving antenna.
   -- Increase the separation between the equipment and receiver.
   -- Connect the equipment into an outlet on a circuit different from that to 
     which the receiver is connected.
   -- Consult the dealer or an experienced radio/TV technician for help.

THIS DEVICE COMPLIES WITH THE CANADIAN ICES-003 

CLASS B SPECIFICATION
CET APPAREIL EST CONFORME AVEC LE CIEM-003 DU 

CANADA CLASSE B SPÉCIFICATION

CAUTION:

Changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate 

the equipment

ATTENTION:

Les changements ou modifications non expressément approuvés par 

la partie responsable de la conformité pourraient annuler l’autorité 

de l’utilisateur à faire fonctionner l’équipement

Summary of Contents for LightSpeaker 5

























Reviews: