Kleinn Air Horns X3-KIT Installation Manual Download | Manualshive

Page: 22 / 40

background image

X3-KIT

Installation and Operation Manual

Go to Table of Contents

PG 22/40

REV: BETA (4/25/2019)

8.4.3.

Install Air Tank Bracket (X3-202, 203 & 204) on chassis tube, using

#H5, H6, H8, H9 & H10, as

shown below. Hand-tighten hardware only, so Bracket can still be rotated and moved along tube.

NOTE: Ensure forward edge of clamp is butted against weld bead on chassis, which increases clearance
between back of X3-203 and springs

. There should be a minimum ¼” clearance to coil spring.

Figure 8

–

Front Air Tank Bracket stops at corner Gusset (Shown with Air Tank)

Figure 9

–

Installing Front Air Tank Brackets, Exploded View

FRONT

Bracket butts up
to Frame Gusset

FRONT

X3-203

H10 (5)

X3-204

X3-202

H5 (3)

H9 (5)

H8 (5)

H6 (2)

«
...
20
21
22
23
24
...
»

Summary of Contents for X3-KIT









































Reviews:

No comments

Related manuals for X3-KIT

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 30

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: IFO Pages: 12

INDUSTRIAL Series

Brand: QC Conveyors Pages: 44

Brand: Manfrotto Pages: 2

Brand: La Crosse Technology Pages: 6

5500DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Maintenence Kits

Brand: Generac Power Systems Pages: 1

Brand: FormFit Pages: 2

WrapAround Windjammer

Brand: Bestop Pages: 7

Ceiling Trim Kit for Home2 Series

Brand: Elite Screens Pages: 8

Brand: nedis Pages: 76

Brand: Orion Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands