Kleenmaid LTK95A Installation Manual Download Page 17

Installation

15

802116

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Water Supply Requirements

NOTE: Water supply faucets must fit standard 
3/4-14 BSP metric female couplings. 
DO NOT USE SLIP-ON OR CLAMP-ON 
CONNECTIONS.

NOTE: Water supply faucets should be readily 
accessible to permit turning them off when washer 
is not being used.

Water Temperature

Cold:

Recommended cold water temperature is 16° to 
27° Celsius (60° to 80° Fahrenheit).

Hot:

Recommended hot water temperature is 49° to 
60° Celsius (120° to 140° Fahrenheit).

Warm:

Mixture of hot and cold water. (Warm water 
temperature is dependent upon the water temperature 
and the pressure of both the hot and cold water supply 
lines.)

IMPORTANT: Turn off water supply faucets after 
check-out and demonstration. Owner should turn 
off water supply whenever there will be an 
extended period of non-use.

NOTE: A longer fill hose is available (as optional 
equipment at extra cost) if the hose (supplied with 
the washer) is not long enough for the installation. 
Order hose as follows:

Part Number 1010102 – 2,5 m Fill Hose

Figure 17 

Water Pressure

Pressure must be a minimum of 138 to a maximum of 
827 kPa (20 to 120 pounds per square inch) static 
pressure measured at the faucet.

NOTE: For water pressure over 827 kPa 
(120 pounds per square inch) we recommend the 
installation of a pressure limiting valve (Part 
Number PSL50DK). This item may be purchased 
by calling 1300 652 100.

NOTE: Water pressure under 138 kPa (20 pounds 
per square inch) will cause an extended fill time in 
the washer and may not properly flush out the 
detergent dispenser.

Under certain conditions, hydrogen gas may 
be produced in a hot water system that has 
not been used for two weeks or more. 
HYDROGEN GAS IS EXPLOSIVE. If the hot 
water system has not been used for such a 
period and before using the washer, turn on 
all hot water faucets and let the water flow 
from each for several minutes. This will 
release any accumulated hydrogen gas. The 
gas is flammable. Do not smoke or use an 
open flame during this time.

W029

WARNING

FLW2008N

1

Water Supply Faucets

2

Cold Water Connection

3

Hot Water Connection

4

Fill Hoses

FLW2008N

1

2

3

WATER 
MIXING 

VALVE

4

Summary of Contents for LTK95A























Reviews: