Strona 13 z 16
rev. 1.0.1
USER MANUAL
:
KIVOS KD700mk2
MULTIPURPOSE WIRELESS VIDEO DOOR PHONE INTERCOM SYSTEM
WITH MULTI MONITOR
www.elmic.pl
,
i.
Password
Enter into Security Password menu.
•
Press “
MENU
” key to choose figure of old or new password.
•
Press“
↑
/
↓
”key
-
》
adjust figure
-
》
press “
OK
” key to set up
•
If original password is right, screen shows “success!”, and then return to the setup menu.
•
If original password is wrong, screen shows “failed”, and then return to code match menu, please set up again
•
Press “
EXIT
” key to turn back to standby mode.
j.
Sense
Enter into Sense setup menu.
•
Press“↑/↓”key -
》
choose “OFF” or “ON” -
》
press ”OK” key to connect to outdoor unit -
》
press ”OK” key to
confirm and exit
•
screen displays “success” when it finish
•
Press“↑/↓”key -
》
choose “Sense auto record”or “Sense nightlight” -
》
press ”OK” key to confirm and exit
•
Press “EXIT” key to turn back to standby mode
k.
Ring
Enter into Ring menu.
•
Press“↑/↓”key -
》
increase and reduce volume(10 levels in total) -
》
press “OK” key to set up and return to
menu.
•
Press “EXIT” key to turn back to standby mode
l.
Reset
Enter into Restore setting menu.
•
Press“↑/↓”key -
》
set up “Yes” or “No” -
》
press ”OK” key to confirm and exit
•
Press “EXIT” key to turn back to standby mode
m.
Code
Enter the Code Menu, input password (0000). If the password is wrong, screen shows "Password error!", "Please input
again!", please input the right password.
Match code function: match code; give code; receive code; inform:
Match code
(Outdoor unit should connect to the Indoor monitor)
•
Select “Match Code” on indoor monitor -
》
press “
OK
” key-
》
enter into the match code mode
•
Under the standby mode of outdoor unit -
》
long press “
call
” key-
》
loosen key until the sound of a “Beep”, enter into
the match code mode
•
If two units match successfully in 16 seconds, indoor monitor displays “Success”, outdoor unit makes “Beep- Beep-
Beep” sounds, as the first outdoor unit
•
If matching failed in 16 seconds, indoor monitor shows “failed”, the outdoor unit makes ”Beep” sound
•
Press “
EXIT
” key on the indoor monitor, exit menu, enter into the standby mode
Notice: If failed match, rematch the code after connection, otherwise, rematch the code after clear the code
Indoor monitor clear code method: refer to the menu function -
》
code -
》
clear code.
Outdoor unit clear code method:
A. Transfomer supply: long press “Clear Code” key about one second, code cleared after a “tick” sound.
B. Battery supply: press “Clear Code” key and “doorbell key” at the same time till a “Beep”, code cleared.
Give code & Receive code
(match more indoor monitors and outdoor units ):
•
Choose “give code” on indoor monitor given or received code-
》
press “
OK
” key-
》
enter into “give code” mode
•
Added indoor monitor enters into the code menu as above steps-
》
choose “receive code” -
》
press “
OK
” key -
》
enter
into the receive code mode.
•
If code receiving finished in 16 seconds, exit code receiving mode after three “beep” sounds, and then enter into code
menu.
•
The added outdoor unit(finished clear code), under the standby mode-
》
keep pressing ”
call
” key for 6 seconds until two
“beep” sounds(“beep” once about 3 seconds) -
》
loosen the key to enter into code receiving mode.
•
Outdoor unit make three “beep” sounds if receive code successfully, and as No. 2 outdoor unit.
