Kiturami KRH-35B Technical Information And Installation Servicing Instructions Download Page 12 | Manualshive

Page: 12 / 39

background image

3. INSTALLATION

3-5-1 CONNECTING WIRES

※

This appliance is designed on

AC 220V ~ 230V/ 50Hz

.

This work of connecting wires is required by a qualified electrician.

1. Make sure that the earth connection is required for safety uses from any electric leakage or short-circuit.

2. Make sure that the connecting electricity - for example, connecting power and cable, wiring, earthing,

etc - should comply with the regulation.

3. If this appliance is not earthed by power plug, ensure to earth separately, by minimum 30cm inserted in the

ground. Note not to connect gas pipe, telephone wire and lightning conductor(rod) in order to avoid any

accident from lightning, surge, or the gas accident.

4. Make sure that the socket outlet is apart by over 30 cm from the appliance.

5. The power outlet has to have at least the minimum clearance of 30mm from the gas boiler

6. The grounding point need to be buried at least 30cm

3-5 CONNECTING ELETRICITY

12페이지

«
...
10
11
12
13
14
...
»

Summary of Contents for KRH-35B








































Reviews:

No comments

Related manuals for KRH-35B

Brand: IBC Pages: 2

Brand: Vaillant Pages: 12

ECO HEAT 10 CA II PLUS

Brand: Gorenje Pages: 74

Brand: Calomax Pages: 14

SYSTEM 2000 Accel CS

Brand: ENERGY KINETICS Pages: 3

Expansion module 1

Brand: Thermia Pages: 28

Brand: Monzana Pages: 7

Brand: Bryant Pages: 14

Classic FF 340 LF

Brand: Ideal Boilers Pages: 40

Brand: Ideal Boilers Pages: 40

Brand: gledhill Pages: 48

Brand: gledhill Pages: 56

DOMIcompact F 24 D

Brand: Ferroli Pages: 40

Brand: Unical Pages: 72

Gas Infrared Salamander Broiler RB36

Brand: Wolf Pages: 2

Promax System HE Plus A Range

Brand: Potterton Pages: 60

Brand: Sime Pages: 40

BlueHelix HiTech RRT C

Brand: Ferroli Pages: 356

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands