4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■
Level
■
Drill 1¼" (3 cm) drill bit
■
For chimney mounting brackets:
³⁄₃₂
" (2.4 mm) drill bit if
installing into wood.
■
For range hood assembly mounting brackets:
¹⁄₈
" (3 mm) drill
bit if installing into wood.
■
Pencil
■
Wire stripper or utility knife
■
Tape measure or ruler
■
Pliers
■
Caulking gun and weatherproof caulking compound
■
Vent clamps
■
Jigsaw or keyhole saw
■
Flat-blade screwdriver
■
Metal snips
■
Phillips screwdriver
■
Scissors
Parts needed
■
Home power supply cable
■
1 - ½" (12.7 mm) UL listed or CSA approved strain relief
■
2 UL listed wire connectors
For vented installations, you will also need:
■
1 wall or roof cap
■
Metal vent system
For non-vented (recirculating) installations, you will also
need:
■
Chimney Kit Part Number 8212713 (Stainless Steel), 8212714
(White), or 8212715 (Black). See “Assistance or Service”
section to order.
Parts supplied
Remove parts from packages. Check that all parts are included.
■
2 metal grease filters for 30" (76.2 cm) models
3 metal grease filters for 36" (91.4 cm) models
■
2 - chimney mounting brackets
■
4 - #8 Phillips head chimney bracket mounting screws
■
2 - #10 Phillips head range hood mounting screws
■
6 - Chimney cover mounting screws
■
Upper chimney cover
■
Lower chimney cover
■
Damper
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the rear wall of the
range hood.
Canopy range hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
The canopy range hood is factory set for venting through the roof
or wall. For non-vented (recirculating) Installation see “Non-
vented (recirculating) Installations” in “Prepare Location” section.
Charcoal Filter Kit Part Number 8285507 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
Vented Installations
30" (76.2 cm)
36" (91.4 cm)
22" (55.9 cm)
Min 27
¹⁄₂
" (69.8 cm)
Max 36
¹⁄₂
" (92.7 cm)
21
¹⁄₄
" (54 cm)
1
¹⁄₄
"
(3.2 cm)
3
¹⁵⁄₁₆
"
(10 cm)
10
¹⁄₄
" (26 cm)
11
¹³⁄₁₆
" (30 cm)
Summary of Contents for W10029780
Page 12: ...12 WIRINGDIAGRAM ...
