KitchenAid Superba Series Installation Instructions Manual Download | Manualshive

Page: 8 / 26

background image

8

Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet included with power
supply cord kit.

Option B, Direct Wire:

Helpful Tip:

Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Drill a

1¹⁄₂

" (3.8 cm) hole in right-hand cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (Part Number 302797 -
not provided).

Route cable from power supply through cabinet hole (cable must
extend to the right front side of cabinet opening). Tape cable to
the floor in area shown. This will prohibit cable from moving when
dishwasher is moved into cabinet opening.

Prepare and Route Water Line

Helpful Tip:

Routing the water line through the left side of cabinet

opening will make water connection easier.

Drill a

¹⁄₂

" (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing for the water supply line.

«
...
6
7
8
9
10
...
»

Summary of Contents for Superba Series



























Reviews:

No comments

Related manuals for Superba Series

Spacemaker WSLP1500JWW

Brand: GE Pages: 3

Brand: Baumatic Pages: 33

Brand: Hotpoint Ariston Pages: 76

Brand: Smeg Pages: 36

Brand: Hotpoint Pages: 2

Brand: Midea Pages: 28

Brand: Mach Pages: 45

Brand: Gaggenau Pages: 68

Brand: Eswood Pages: 13

Brand: Samsung Pages: 88

Brand: Samsung Pages: 88

Brand: Samsung Pages: 128

Brand: Samsung Pages: 68

Brand: Alliance Laundry Systems Pages: 38

Brand: inventum Pages: 104

Brand: Bosch Pages: 64

Brand: Bosch Pages: 48

Brand: Bosch Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands