KitchenAid Superba Series Installation Instructions Manual Download | Manualshive

Page: 7 / 26

background image

7

INSTALLATION INSTRUCTIONS

Prepare Cabinet Opening—Existing Utilities

If the water line and the cable extend to the locations shown,
proceed to the “Install Drain Hose” section. If they do not reach far
enough, follow the instructions in the “Prepare Cabinet Opening—
New Utilities” section.

Prepare Cabinet Opening—New Utilities

Prepare and route the electrical supply

Option A, Power Supply Cord:

NOTE:

A grounded 3 prong outlet is required inside a cabinet next

to the dishwasher cabinet opening.

Drill a

1¹⁄₂

" (3.8 cm) hole in cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

WARNING

Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

«
...
5
6
7
8
9
...
»

Summary of Contents for Superba Series



























Reviews:

No comments

Related manuals for Superba Series

WD22T6300 Series

Brand: Samsung Pages: 136

Brand: Indesit Pages: 24

Brand: Gorenje Pages: 18

Brand: Fisher & Paykel Pages: 20

Brand: CDA Pages: 44

HG6085D137609HW

Brand: Hanseatic Pages: 78

MDC4650AWB - Jet Clean II 24" Portable Dishwasher

Brand: Maytag Pages: 2

WF80F7E6U6 Series

Brand: Samsung Pages: 48

Brand: Samsung Pages: 76

Brand: Samsung Pages: 40

Brand: Goddess Pages: 24

Brand: Lumina Pages: 18

Brand: Concept2 Pages: 112

Brand: Haier Pages: 44

Brand: Haier Pages: 56

Brand: Haier Pages: 44

Brand: Haier Pages: 100

Brand: Haier Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands