4
Parts needed
■
Home power supply cable
■
1 - ½" (12.7 mm) UL listed or CSA approved strain relief
■
3 UL listed wire connectors
■
1 wall or roof cap
■
Metal vent system
■
Blower motor system - internal or external (see “Blower
Motor System” in the “Accessories” section.)
Parts supplied
Remove parts from packages. Check that all parts are included.
■
2 metal grease filters for 30" (76.2 cm) and 36" (91.4 cm)
models
3 metal grease filters for 48" (121.9 cm) models
■
Range hood canopy with halogen lamps installed.
■
1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct
transition with damper
■
Wood support
■
Grease drip trays
■
4 - 6 x 80 mm mounting screws
■
4 - 3.5 x 9.5 mm screws
■
6 - 4.2 x 19 mm screws
■
2 - D5.3 x 20 mm washers
■
2 - 10 x 50 mm wall anchors
■
T-20 TORX
®†
adapter
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the rear wall of the
range hood.
Canopy range hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
The canopy range hood is factory set for venting through the roof
or through the wall.
All openings in ceiling and wall where canopy range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
Front view
Back view
Optional Full-Width Duct Cover Installations
†®TORX is a registered trademark of Saturn Fasteners, Inc.
A. Knockout into terminal box
B. Top of hood
C. Wood support
D. Bottom of hood
A. Optional full-width duct cover
B. Range hood
CL
18
¹⁄₁₆
" (45.9 cm) for 48" (121.9 cm) Hood
12
¹⁄₁₆
" (30.6 cm) for 36" (91.4 cm) Hood
9
¹⁄₁₆
" (23.0 cm) for 30" (76.2 cm) Hood
18" (45.7 cm)
12" (30.5 cm)
30" (76.2 cm)
36" (91.4 cm)
48" (121.9 cm)
3
³⁄₁₆
"
(8.1 cm)
6
¹⁄₂
" (16.5 cm)
25" (63.5 cm)
A
B
C
CL
18
¹³⁄₁₆
" (47.8 cm) for 48" (121.9 cm) Hood
12
¹³⁄₁₆
" (32.5 cm) for 36" (91.4 cm) Hood
9
¹³⁄₁₆
" (24.9 cm) for 30" (76.2 cm) Hood
18"
(45.7 cm)
D
9
⁵⁄₈
"
(24.4 cm)
12"
(30.5 cm)
18"
(45.7 cm)
12"
(30.5 cm)
A
B
