background image

8

REFRIGERATION SYSTEM DIAGNOSIS GUIDE

COMP.

DIS-

CHARGE

Very hot

Slightly

warm
to hot

Hot

Very hot

Room temp.

(cool)

Cool to hot

CON-

DENSER

Very hot

Warm

Top pass

warm

Lower pass

cool (near

room temp)

due to liquid

Room temp.

Room temp.

Room temp.

CAPILLARY

TUBE

Warm

Cool

Warm

Room temp.

(cool) or

colder

Room Temp.

(cool)

Room temp.

(cool)

EVAP.

Cold

Cold

Extremely

cold neat

inlet - Outlet

below room

temp.

Extremely

cold near

inlet - Outlet

below room

temp

No refrigera-

tion

No refrigera-

tion

WATTAGE

Normal

Higher than

normal

Lower than

normal

Lower than

normal

Lower than

normal

Lower than

normal

SUCTION

LINE

Slightly

below room

temp.

Very cold
may frost

heavily

Warm -

near room

temp.

Warm -

near room

temp.

Room temp.

(cool)

Room temp.

(cool)

COMPRESSOR WINDING RESISTANCE

To measure start winding resistance, measure across the Common (C) and Start (S) pins.
To measure run winding resistance, meausre across the Common (C) and the Run (R) pins.

When measuring resistance between the Common (C), Start (S) or Run (R) pins to ground, meter
should read infinity.  Any resistance indicates a shorted compressor.

Specifications:

Start Winding Resistance C to S:

28 ohms

Run Winding Resistance C to R:

8 ohms

Pin Configuation:

C = Common
R = Run
S = Start

S

C

R

Pin Configuation

SYSTEM

CONDITION

NORMAL

OVER-

CHARGE

UNDER-

CHARGE

PARTIAL

RE-

STRICTION

COMPLETE

RE-

STRICTION

NO GAS

SUCTION

PRESSURE

Normal

Higher than

normal

Lower than

normal

Somewhat

lower than

normal-in

vacuum

In deep

vacuum

0PSIG

to

25" vacuum

Summary of Contents for KUWS246

















Reviews: