background image

12

3-Wire Connection: Direct Wire

Use this method only if local codes permit connecting ground 
conductor to neutral supply wire.

1.

Pull the wires through the conduit on cord/conduit plate on 
bottom of range. Allow enough slack to easily attach the 
wiring to the terminal block.

2.

Attach terminal lugs to line 2 (red), bare (green) ground, and 
line 1 (black) wires. Loosen (do not remove) the setscrew on 
the front of the terminal lug and insert exposed wire end 
through bottom of terminal lugs. Securely tighten setscrew to 
torque as shown in the following Bare Wire Torque 
Specifications chart.

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

3.

Use 

³⁄₈

" nut driver to connect the bare (green) ground wire to 

the center terminal block post with one of the 10–32 hex nuts.

4.

Connect line 2 (red) and line 1 (black) wires to the outer 
terminal block posts with 10-32 hex nuts.

5.

Securely tighten hex nuts.

6.

Replace terminal block access cover.

7.

Slide range backs so that the rear range foot is engaged in 
the anti-tip bracket slot.

A. Terminal block
B. Ground-link screw

C. Cord/conduit plate

D. Line 2 (red) wire

E. Bare (green) ground wire

F. Line 1 (black) wire

A. Terminal lug
B. Setscrew

C. Line 2 (red) wire
D. Bare (green) ground wire

E. Line 1 (black) wire

A

B

C

D

E

F

A

B

C

D

E

Wire Awg

Torque

8 gauge copper

25 lbs-in. (2.8 N-m)

6 gauge aluminum

35 lbs-in. (4.0 N-m)

A. 10–32 hex nut
B. Line 2 (red)

C. Ground-link screw

D. Bare (green) ground wire

E. Line 1 (black)

F. Terminal lug

B

F

A

E

D

C

Summary of Contents for KFEG500EBS

















Reviews: