background image

INSTALLATION INSTRUCTIONS

30" (76.2 CM) FREESTANDING ELECTRIC RANGES

Table of Contents

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS................................................ 3

Tools and Parts ............................................................................ 3
Location Requirements................................................................ 3
Electrical Requirements ............................................................... 5

INSTALLATION INSTRUCTIONS.................................................. 6

Unpack Range ............................................................................. 6
Install Anti-Tip Bracket................................................................. 6
Electrical Connection ................................................................... 8
Verify Anti-Tip Bracket Is Installed and Engaged...................... 13
Level Range ............................................................................... 13
Warming Drawer or Premium Storage Drawer.......................... 14
Storage Drawer .......................................................................... 14
Complete Installation ................................................................. 15
Moving the Range...................................................................... 15

IMPORTANT:

 

Save for local electrical inspector's use.

W10694026A

Summary of Contents for KFEG500EBS

















Reviews: