background image

4  

|  COMMERCIAL BLENDER SAFETY

COMMERCIAL BLENDER SAFETY

5. Children should be supervised to ensure that they do 

not play with the appliance.

6. This appliance shall not be used by children under  

8 years. Keep the appliance and its cord out of reach 

of children.

7. Never leave the Blender unattended while it is in 

operation.

8. Avoid contacting moving parts. Keep hands, hair, 

clothing, as well as spatulas and other utensils away 

from blade during operation to reduce the risk of injury 

to persons and/or damage to the Blender. 

9. Unplug from outlet when not in use, before putting  

on or taking off parts, and before cleaning.

10. Do not operate any appliance with a damaged cord  

or plug or after the appliance malfunctions or has  

been damaged in any manner. Return appliance to  

the nearest Authorised Service Centre for examination, 

repair or adjustment. If the supply cord is damaged, 

it must be replaced by a special cord or assembly 

available from the manufacturer, its service agent, or 

similarly qualified persons in order to avoid a hazard.

11. Do not let cord hang over edge of table or counter. 

12. The blades are sharp. Care should be taken when  

handling the sharp cutting blades, emptying the jar, 

and during cleaning.

13. Keep hands and utensils out of jar while blending to 

reduce the risk of severe injury to persons or damage 

to the Blender. A scraper may be used, but must be 

used only when the Blender is not running.

14. Do not use the Blender outdoors.

15. Be careful if hot liquid is poured into the Blender as 

it can be ejected out of the appliance due to sudden 

steaming.

16. Always operate Blender with lid in place.

17. The use of attachments not recommended or sold by 

KitchenAid may cause fire, electric shock, or injury. 

Summary of Contents for 9KSBC2F1













Reviews: