manualshive.com logo in svg

Kitagawa MR250RAE13, Instruction Manual

Share
Download
Kitagawa MR250RAE13 Instruction Manual Download Page 46

40 

Exterior type rotary joint

Supply part

 

Spacer

Jig mounting reference plane 

Supply part

Discharge 

opening face

Discharge 

opening face

 

Jig mounting 

reference plane

 

Spacer

 

18. Mounting Rotary Joint (Option) 

18-1. Alignment of discharge opening face 

To mount the rotary joint, the rotary joint discharge opening face must be aligned with the 

jig mounting reference plane so that hydraulic oil does not leak to the jig (A-size in the 

following figure). 

To align the position of the rotary joint discharge opening face, the thickness of the spacer 

attached to the rotary joint must be adjusted (B-size in the following figure). 

When the rotary joint is mounted additionally or a set of rotary joint parts is replaced, check 

the product type and manufacturing number, and contact Kitagawa branch or your agent. 

 

 

 

 

 

                   

 

 

 

18-2. Pining to supply part 

To route the pipe to the supply part of the rotary joint, determine a hose length so that the 

hose will not be moved by the movement of a table for a mounted machine. 

Moreover, when turning a joint screw, use the tightening tool carefully so that unreasonable 

force will not be applied to the supply part. 

Built-in type rotary joint

 

Summary of Contents for MR250RAE13



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands