background image

Roman Shades Collection

Automation 

Installation Instructions

GETTING STARTED 

Product View  ................................................................................................................................................................ 1
Tools and Fasteners Needed  ....................................................................................................................................... 2

INSTALLATION 

Installation Overview  ................................................................................................................................................... 2
Mount the Installation Brackets - Inside Mount with Valance   ............................................................................... 3
Mount the Installation Brackets - Inside Mount without Valance   ......................................................................... 4
Mount the Installation Brackets - Outside Mount without Valance   ...................................................................... 6
Mount the Installation Brackets - Outside Mount with Valance   ............................................................................ 7
Install the Shade  ........................................................................................................................................................... 9
Install the Shade into the Brackets   ........................................................................................................................... 9
Attach the Valance Fabric (If Applicable)   ............................................................................................................... 10
Connect the Power Source  ....................................................................................................................................... 11

OPERATION

Testing the Shade  ...................................................................................................................................................... 14
Using the Automation Remote ................................................................................................................................. 14
Resetting the Shade (If Necessary)  .......................................................................................................................... 15
Troubleshooting  ......................................................................................................................................................... 16

CARE

Removing the Shade (If Necessary)  ......................................................................................................................... 18
Dressing Kirsch Roman Shades   ............................................................................................................................... 18
Cleaning Procedures  .................................................................................................................................................. 18

WARRANTY

 .................................................................................................................................................................. 19

Rev. A   9/3/19

Summary of Contents for Roman Shades Automation





















Reviews: