background image

AUXILIARY FUNCTIONS

10

9

the scanning pause, the radio will transmit from the currently working 
channel.

Note:

Currently working channel means the channel in which the radio 

holds on under the following four conditions.
1)  After receiving the signals, the radio will still stay in the current 
channel before restarting the scan. 
2)  When receiving signals during scanning, the radio will pause on 
the current channel and will keep staying on it for 3 seconds after the 
signals disappear.
3)  Radio will stay on the current channel when pressing PTT during 
scanning.
4)  When the radio transmitting ends by releasing PTT button, within 
the transmitting pause time preset by the local dealer, the radio will 
stay in the current channel.

Selected channel: The first channel in the scanning list set by the 

dealer.

Priority channel: The prior channel in the scanning list set by the 

dealer.

Only when priority channel has been selected, the options of 

/

 

 

priority channel 

0

and

  

/

priority c currently working channel 

0

  

in Revert Channel are available. 

      

 TIME-OUT TIMER

Time-out timer can prevent the user from continuously talking 
overlong and prevent the radio body heating due to continuous 
longtime transmitting.
If you continuously transmit longer than the time limit preset by the 
dealer, the radio will stop transmitting and warning tone sounds, and 
to stop the warning tone please release the PTT button. Pressing the 
PTT button again will resume transmitting.

       

BATTERY SAVING

The automatic battery saving function decreases the power 
consumption when no signal is received and no operation is 
conducted.
If the battery saving function is activated, 10 seconds after the radio 
doesn't receive any signals or no operation is being conducted, the 
radio enters battery saving mode. When a signal is received or any 
operation occurs, it exits battery saving mode automatically.

       

LOW BATTERY WARNING

When the battery power goes below a certain value in transmitting, 
LED flashes red and Low battery warning tone sounds and then the 
radio stop transmitting. You need to recharge or change the battery.

       MONITOR
Off:

 When this function is selected, no operation is performed.

Monitor Momentary: 

Press and hold the monitor button to 

deactivate the signaling temporarily, and squelch un-mutes. Release 
it to return to normal operation and squelch mutes.

Summary of Contents for PT4200













Reviews: