Kipor SINEMASTER IG4300 Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 50

Kipor SINEMASTER IG4300 Owner'S Manual Download Page 47

41

14. EMISSION CONTROL SYSTEM

If  so  designated,  your  generator  has  an  engine  that  has  been  approved  by  the  California  Air
Resources  Board.  Other  than  the  tune  up  procedures  specified  in  the  maintenance  section,  no
additional maintenance is required.

The emission control system has the following components:

1. Fuel System: The fuel tank, cap, indicator and hoses are specially designed and constructed

to not allow fuel vapors to permeate and be released to the atmosphere.

2. A carbon activated canister collects gasoline vapors from the fuel tank and returns them to the

combustion chamber for burning.

3. A catalyst is built into the muffler to further treat the engine exhaust.
4. A secondary air injection valve adds combustion air to ignite unburned fuel in the exhaust.

Contact your authorized Kipor service center to obtain the correct replacement parts and service on
this system.

Inlet System

空滤

器底

壳

六角

法兰

面螺

母M6

滤芯

组件

空滤

器盖

接碳

罐负

压管

主量

孔

(出厂

前已

调节

)

化油

器部

件

Air filter housing

Flange nut M6

Filter element

Air filter cover

Carburetor

Main metering jet

Canister
connection

«
...
45
46
47
48
49
...
»

Summary of Contents for SINEMASTER IG4300



















































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands