manualshive.com logo in svg

KINNEY KLRC125, Operator'S Manual, Page: 9 / 50

Share
Download
KINNEY KLRC125 Operator'S Manual Download Page 9

4

Manual 4804 Rev E p/n 004804 0000

GRAPHIC CONVENTIONS USED IN 
THIS MANUAL

The following hazard levels are referenced within 

this manual:

DANGER

!

Indicates a hazardous situation that, if not 

avoided, will result in death or serious injury.

WARNING

!

Indicates a hazardous situation that, if not 

avoided, could result in death or serious 

injury.

CAUTION

!

Indicates a hazardous situation that, if not 

avoided, could result in minor or moderate 

injury.

Indicates a situation that can cause damage 

to the engine, personal property, and/or 

the environment or cause the equipment to 

operate improperly.

OTE:  

N

Indicates a procedure, practice, or 

condition that should be followed in 

order for the equipment to function in the 

manner intended.

SAFETY INSTRUCTION TAG

CAUTION

!

Do not valve or restrict pump discharge 

opening.
Use oil mist eliminator when operating pump,  

and ensure adequate ventilation when 

discharging indoors.
Refer to manual safety instructions.

SAFETY PRECAUTIONS FOR LIQUID 
RING PUMPS

Please read the following safety information before 

operating the vacuum pump.

•  Do not operate the pump without the coupling 

or belt guard properly attached. Disconnect the 

pump motor from the electrical supply at the 

main disconnect before removing the coupling 

or belt guard. Replace the coupling or belt guard 

before reconnecting the power supply to the 

pump motor. Operating the pump without the 

coupling or belt guard properly installed exposes 

personnel in the vicinity of the pump to risk from 

rotating drive components.

SAFETY

02

Summary of Contents for KLRC125



















































Reviews:

No comments