KINNEY KLRC125 Operator'S Manual Download Page 6

Page: 6 / 50

Manual 4804 Rev E p/n 004804 0000

CONGRATULATIONS

on the purchase of a new

Kinney

KLRC™

Liquid Ring Vacuum Pump.

Please examine the pump for shipping damage,

and if any damage is found, report it immediately to

the carrier. If the pump is to be installed at a later

date, make sure it is stored in a clean, dry location

and rotated regularly. Make sure covers are kept

on all openings. If the pump is stored outdoors, be

sure to protect it from weather and corrosion.

Kinney KLRC

vacuum pumps are built to exacting

standards and, if properly installed and maintained,

will provide many years of reliable service. Read

and follow every step of these instructions when

installing and maintaining your pump. We have

tried to make these instructions as straightforward

as possible. We realize getting any new piece

of equipment up and running in as little time as

possible is imperative to production.

WARNING

Serious injury can result from operating or

repairing this machine without first reading the

service manual and taking adequate safety

precautions.

OTE:

Record the pump model and serial

numbers in the OPERATING DATA form

on the inside back cover of this manual.

Use this identification on any replacement

part orders, or if service or application

assistance is required.

MODELS COVERED BY THIS
MANUAL

This manual contains installation, operation,

and maintenance procedures for KLRC-40 to

KLRC-951. The nameplate on the pumps

provides a letter coding for pump material and

shaft seal type in the suffix following the KLRC

model number.

NAMEPLATE DATA

The first letter designates the standard materials of

construction:

Cast iron casing, bronze impellers, 316

stainless steel shaft and steel trim

Cast iron casing with stainless steel 316L

impellers and 316 shaft and steel trim

All stainless steel 316L pump, except for the

outboard ball bearings, bearing end caps,

and steel trim

The second suffix letter designates the standard

type of shaft seal:

John Crane Type 21 seal - Carbon/Ceramic/

Viton

Flow Serve RO Dura Seal - Carbon/

Durachrome/Viton

PTFE Encapsulated Viton O-Rings

DD Flow Serve Double RO Dura Seal

INTRODUCTION

Summary of Contents for KLRC125



















































Search results

Summary of Contents for KLRC125

Reviews:

Related manuals for KLRC125

Brands by name

Popular brands

KINNEY KLRC125, Operator'S Manual

Search results

Summary of Contents for KLRC125

Reviews:

Related manuals for KLRC125

Brands by name

Popular brands