background image

012696  GL0011P-07 

– Installation Guidelines for BioDisc BA, BAx, BB & NB Units 

    Page  10 

Control Panel Installation 

4.1 

General Installation 

4.1.1 

The control panel need not be adjacent to the plant. It can be wall mounted or fixed to the mounting 
frame (available separately). It should be positioned so it cannot be reached by someone standing in 
or on the BioDisc unit. 

4.1.2 

The control panel should be fitted by a qualified electrician working to the latest IEE Regulations. 

4.2 

Mounting Frame Installation (where applicable) 

4.2.1 

Set the frame legs in a concrete base, minimum 250mm thick and prop the frame to prevent 
movement until the concrete has set. 

4.2.2 

Allow 350mm minimum clearance from finished ground level to the bottom of the panel. 

4.3 

Installation of Control Panel  

Figure 1 : Control Panel 

4.3.1 

Remove the four screws on the front of the panel and remove the main cover. 

4.3.2 

Remove the four screws holding the safety cover and remove the safety cover. 

4.3.3 

Remove the two screws holding the isolating cover and remove the isolating cover. 

4.3.4 

Using a suitable M20 gland, feed the mains power supply through Gland Hole 1 (Figure 1). Wire the 
mains supply to the terminal blocks following the guide on the connections. 

4.3.5 

Replace the isolation cover and screws. 

4.3.6 

Using a suitable M20 gland, feed the motor power supply cable through Gland Hole 4 (Figure 1) and 

terminate to connections 5 & 6 (TB3) following the guide on Table 2. 

 

    2        3           4 

 5 

    6        7            8 

  9 

Main Cover 

Isolating Cover 

Safety Cover 

Summary of Contents for BioDisc BA














Reviews: