background image

Installation Instructions

Model Number VFI30 Gas Fired Direct Vent Room 

Heater Inserts

Model VFI30

Listed Certified for USA, and Canada

Minimum Fireplace Opening Required: 29”W x 20 3/4”H x 16 1/2”D

Certified to: ANZI Z21.88-2009, CSA2.33-2009

Read this complete manual before beginning installation.

These instructions must be kept with the unit for future reference.

FOR YOUR SAFETY

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.

WARNING: The VFI30

Fireplace Insert was designed for
installation in a solid fuel fireplace
that has been installed in
accordance with national,
provincial/state and local building
codes and is constructed of
noncombustible materials. Do not
remove any refractory materials
from any masonry solid fuel
fireplace.

The VFI30 Fireplace Insert was
designed for installation in a zero
clearance type listed solid fuel
burning factory built fireplace. It may
be necessary to remove the damper
plate, refractory liners, log grates,
glass door, and screen rails/mesh.
Removal of the smoke baffle is
necessary in most cases.

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause property damage, personal
injury or loss of life. Refer to this manual. Installation and service
must be performed by a qualified installer, service agency or the
gas supplier.

Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.

What to Do If You Smell Gas

Do not try to light any appliance.

Extinguish any open flame.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbour’s phone.

If you can not reach your gas supplier, call the fire department.

A Division of R-Co. Inc.

2340 Logan Avenue

Winnipeg, Manitoba, Canada  R2R 2V3

Ph: (204) 632-1962

Printed in Canada October 19, 2009  30 VFI-MAN

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases, unless a certified kit is used.

Summary of Contents for VFI30





























Reviews: