Kingsman Fireplaces HBZDV4736 Installation Instructions Manual Download Page 1

Page: 1 / 81

SOLACE/SKYLINE

Installation Instructions

MQHBZDV3636, MQHBZDV4236, MQRB4236T, HBZDV4736

Models:

MQHBZDV3636N, MQHBZDV3636NE, MQHBZDV3636NE2, MQHBZDV3636LP, MQHBZDV3636LPE,

MQHBZDV3636LPE2

Models:

MQHBZDV4236N, MQHBZDV4236NE, MQHBZDV4236NE2, MQHBZDV4236LP, MQHBZDV4236LPE,

MQHBZDV4236LPE2

Models:

MQRB4236NT, MQRB4236NTE, MQRB4236NTE2, MQRB4236LPT, MQRB4236LPTE, MQRB4236LPTE2

Models:

HBZDV4736N, HBZDV4736NE, HBZDV4736NE2, HBZDV4736LP, HBZDV4736LPE, HBZDV4736LPE2

Certified to:

ANSI Z21.88-2017 • CSA 2.33-2017 Vented Gas Fireplace Heaters, CSA 2.17-2017

A Division of R-Co. Inc.

2340 Logan Avenue

Winnipeg, Manitoba, Canada R2R 2V3

Ph: (204) 632-1962

Printed in Canada February 9, 2021

Part # 36MQ-MAN17

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

For Propane Horizontal installations the venting

must be a minimum of one foot vertical off the

flue before going horizontal.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases,

unless a certified kit is used.

VENTED GAS FIREPLACE HEATER:

NOT FOR USE WITH SOLID FUEL.

Summary of Contents for HBZDV4736


















































































Search results

Summary of Contents for HBZDV4736

Reviews:

Related manuals for HBZDV4736

Brands by name

Popular brands

Kingsman Fireplaces HBZDV4736, Installation Instructions Manual

Search results

Summary of Contents for HBZDV4736

Reviews:

Related manuals for HBZDV4736

Brands by name

Popular brands