background image

-7-

Thank you for choose KINGREX SLAP. It provides you with better protection for connected equipment. 

We sincerely hope you could keep the user manual for whole SLAP life.

    Please read this user manual very carefully. It provides safety, installation, and operating instructions   

    that will help you derive the over all performance and fully extend the life that the SLAP has to offer.     

     Please save this manual! It includes important instructions for the safely use SLAP and for obtaining 

    factory service should the proper operation of the SLAP come into question. 

    Please save or recycle the packaging materials! The SLAP’s shipping materials were designing with  

    great care to provide protection from transportation related damage. These materials are invaluable if 

    you ever have to return the SLAP for service. Damage sustained during transit is not covered under 

    the warranty.

To reduce the risk of electric shock, disconnect the SLAP from the mains supply before installing an 

amplifier . Reconnect the power cord only after signaling interconnections have been made. 

    1.  Do not dispose of batteries in a fire, the battery may explore. 

    2.  Do not open or mutilate the battery, released electrolyte is harmful to the skin and eyes.

A battery can present a risk of electric shock and high short circuit current. The following precaution 

should be observed when working on batteries 

    1.  Remove watches, rings or other metal objects. 

    2.  Use tools with insulated handles. 

-   

Caution

: Risk of electric shock - hazardous live parts inside this unit are energized from the     

                    battery supply even when the input AC power is connected. 

-   

Caution

: Risk of electric shock, do not remove cover. No user serviceable parts inside, Refer 

                    servicing to qualified service personnel. 

-   

Warning

: To reduce the risk of fire, replace only with the same type and rating of fuse. 

-   

Warning

: To reduce the risk of fire or electric shock, install in temperature and humidity controlled 

                     indoor area of conductive contaminants.   

Important safety instructions 

   

Safety caution! 

Summary of Contents for SLAP

















Reviews: