background image

www

.kingnodetech.com

Part II Safety Precautions

In order to avoid personal injury caused by improper use of the equipment, 

please read and follow the safety instructions carefully:
1

Please read this operation manual carefully before using the equipment 

to ensure that you have fully understood the performance of the equipment 

and mastered the correct operation and maintenance methods.
2

If the machine is not installed and used in accordance with the operating 

instructions, this product may generate radio energy, which may cause 

interference to radio communications, however it fully complies with the 

relevant provisions of the FCC. If the device is used in a residential area, 

necessary measures need to be taken to eliminate the interference of the 

device with radio communications.
3

Prior to cleaning of the tape jam, make sure the power is turned off. 

When there is a need of professional cleaning for the equipment which 

might lead a breakdown or damage of the machine, you need to get a 

technician to service the machine specifically.
4

When the equipment is necessary to be moved to the next workplace, 

please ensure that the power is off, then remove the Water Bottle, Water 

Tank and the Moistening Brushes to prevent electric shock hazard due to 

the spill of water.
5

The remaining heat exists on the surface of the metal parts attached to 

the heater may cause severe skin burn. Please do not touch it without 

taking any protective measures.
6

Use of tape products or machine parts not recommended by the 

equipment manufacturer may increase unsafe factors.

Technical Parameter Data

Illustration of the Machine

Part III Technical Data and Illustration

Carton Dimension (mm)

Product Dimension (mm)

Gross Weight (kg)

Net Weight (kg)

Electric Voltage (V)

Operationg Frequency (Hz)

Battery Capacity (mA)

Tape Width (mm)

Diameter Roll (mm)

Capacity Of Water Bottle (L)

Brushes Piece/Set

Moistening Pressure Plate Piece/set

E-404

MODEL

E-404H

E-404BH

585*355*350
510*252*266

13

11.6

100-240

50~60

/

≤76 

≤200 

1.73 

2

585*355*350

510*252*266 

13.4

12

100~240

50~60

/

≤76 

≤200 

1.73 

2

585*355*350

510*252*266 

14.8
13.4

100~240

50~60

≤12500

≤76 

≤200 

1.73 

2

03

04

Technical Data Of E-404 Series WAT Kraft Paper Tape Dispenser:

Figure 1: Illustration of the Machine

Summary of Contents for E-404 Series









Reviews: