background image

WARRANTY INFORMATION

2-YEAR 

LIMITED WARRANTY 

FOR THIS 6” BENCHTOP JOINTER 

kING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY 

INTENDED FOR NON COMMERCIAL USE

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centres across Canada.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be liable

for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products. 

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized

King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized

service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

kING CANADA INC. DORVAL, qUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

Summary of Contents for KC-6HJC











Reviews: