background image

Before installing the product ascertain that safety conditions are observed according to the law, rules and regulation.

Use personal safety devices and locate warning signs on the motorized gate.          

Unfulfilment of the below listed direction will release the King gates srl from any responsibility for 

damage caused to people or things.

-Ascertain the intigrity of the packing when opening it.

-In case of anomalies in the functioning, turn immediatly off the gear-motor, disconnect electrical power and operate the gate 

manually the problem has been found and salved.

-Do not modify the product in any part.

-Only authorized and qualified staff is alloned to disassemble the product. 

-Prevent any part of the automation from being next to any source of heat or in contact with liquid substances.

-Use only adeguate power supply cables.

-To optimize the functioning of the automation, King gates accessories only.

-Disposal of waste material has to observe local regulations. 

-Installing, testing and first functioning have to observe the laws in force.    

WARNINGS 

MAIN FEATURES 

TYPICAL SYSTEM 

1    Gear-motor 

2    Photocell 

3    Flashing-light 

4    Key selector 

5    Adaptor arm 

Power supply 

 230 

Motor power supply 

 24 

Electrical input 

 0.8 

Working temperature 

 -20 ÷ +55 

10 

Max dimensions sectional doors 

10 

Max dimensions overhead doors 

M8, Z18 

Transmission gear 

9 - 16 

Speed 

60 

414x264x110 

Frequency of use 

37 

Motorgear dimensions 

(Vac 50Hz) 

(Vdc) 

(A) 

(°C) 
(m ) 

(m ) 

(cm/sec.) 

(%) 

(mm) 

Slide thickness 
Limit switch 

(mm) 

Encoder with mechanical stop 

230 

24 

1.3 

9 - 16 

-20 ÷ +55 

17 
14 

M8, Z18 

 

60 

414x264x110 

37 

Encoder with mechanical stop 

Rolls 1200 

Rolls 700

Max thrust 

700

(N) 

1200 

 TECHNICAL SPECIFICATIONS AUTOMATION 

Transformer power supply 

 230 

Control unit power 

 230 

Max current peak from the motor 

Accessories power 

 24 (400mA) 

-20 ÷ +55 

Environmental operating temperature 

230 (max 40W) 

Courtesy light 

Activated by remote control 

Courtesy light operation 

433 MHz incorporated with 180 storable codes

Receiver 

(Vac) 
(Vac) 

(A) 

(Vdc) 

(°C) 

(Vac ) 

24 (max 15W) 

Flash light 

(Vdc) 

Star GDO 100 

Motor output 

24 (max 100Watt) 

(Vdc) 

TECHNICAL SPECIFICATIONS STAR GDO100 

Summary of Contents for ISTBJV01



















Reviews: