STANDARD/OPTIONAL ACCESSORIES
& MAINTENANCE
MAINTAINING YOUR VACUUM AND ACCESSORIES
Warning! To reduce the risk of injury and electrical shock, unplug the power cord from
the power source. Airborn dust will be produced when cleaning, wear dust mask!
To maintain peak vacuum performance, the foam and re-usable filters must be cleaned often.
When not in use, wrap the power cord around the power cord posts (top handle).
Filter maintenance
- Clean the foam filter and re-usable filter by washing them inside out in a mild
soapy water and then rince with clean water, see Fig.17. Clean optional cartridge filter in a mild
soapy water and then rince with clean water. Allow these filters to dry completely before using.
Blower foam pad maintenance
- After using the detachable blower, make sure the bottom of the
blower is not blocked by debris or leaves. The blower unit comes with an internal foam pad (A)
Fig.18. If this foam pad needs cleaning, remove the four screws that hold the bottom shield.
Remove bottom shield (B) and the foam pad from the blower unit.Clean the foam pad in a mild
soapy water and then rince with clean water. Allow the foam pad to dry completely before
reinstalling it into the lower unit.
General Maintenance and Inspection
- The inside of the tank, hose, extension wands and
accessories should be cleaned after every use, this cleaning should only be done outdoors with
the power cord disconnected from the power source. Check the condition of the power cord and
make sure it is not damaged. Also check the condition of the filters for tears and small holes. Do
not use filters with tears or small holes, replace with new filters.
TROUBLESHOOTING
Dust comes from the motor cover
-
Place/replace the dust bag if dust bag is missing or damaged or empty the tank.
Reduced efficiency/increased motor speed
-
Inlet is block or tank is full- Unblock inlet or empty tank through tank drain.
FIGURE 17
Model
KVAC-1010
KVAC-1040
KVAC-1060
KVAC-1070
KVAC-1183
KVAC-1101
KVAC-1103
KVAC-1105
KVAC-1107
KVAC-1111
KVAC-1117
KVAC-1124
KVAC-1125
KVAC-1126
KVAC-1130
KVAC-1132
Description
30L Dust bags- 3pc. kit
Foam Filter- 1pc.
Re-usable Filter- 1pc.
Cartridge Filter- 1pc.
6ft x 1-1/4” hose
1-1/4” Round Brush- 1pc.
1-1/4” Gulper Tool- 1pc.
1-1/4” Crevice Tool- 1pc.
10” x 1-1/4” Floop Sweep- 1pc.
2pc. Extension wand kit
2-1/2” Blower extension
Caster Wheels- 4pc. kit
2-1/2” Cone nozzle
2-1/2” Blower nozzle
High Efficiency Cartridge Filter
30L High Efficiency Dust bags- 3pc. kit
Included/Optional
Optional
1pc. Included
1pc. Included
Optional
1pc. Included
Optional
Optional
1pc. Included
1pc. Included
2pc. kit Included
1pc. Included
4pcs. Included
1pc. Included
1pc. Included
Optional
Optional
Usage
Dry Vacuuming Applications
Wet•Dry Vacuuming Applications
Wet•Dry Vacuuming Applications
Dry Vacuuming Applications
General purpose
Upholstery and car interiors
General purpose
General purpose
General purpose-reversible attachment
General purpose
Blower
Replacement kit
Blower
Blower
Drywall and fine dust applications
Drywall and fine dust applications
STANDARD AND OPTIONAL ACCESSORIES
The following chart lists the standard accessories included and the available optional accessories for this wet•dry vacuum. Please note that
these accessories are not covered under warranty and are available at your nearest King Canada distributor.
FIGURE 18
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
