Kinetico 2030s, Owner'S Manual

Page: 11 / 37

20 21
Model 2025s 2030s 2040s with
Overdrive 2050s Europe
Only 2060s 2060s with
Overdrive 2100s 2100s with
Overdrive 2175s 4040s with
Overdrive 4050s Europe
Only 4060s with
Overdrive
Activated
Carbon 4060s with
Overdrive -
Macrolite
®
Certified Flow Rate@
15 psi (or less) 8 GPM
30.28 L/min 9 GPM
34 L/min 11 GPM
41.6 L/min 6 GPM
22.71 L/min 11.5 GPM
43.5 L/min 20.5 GPM
77.6 L/min 12 GPM
45.4 L/min. 21 GPM
79.4 L/min 16 GPM
60.5 L/min 11 GPM
41.6 L/min 6 GPM
22.7 L/min 11 GPM
41.6 L/min 10 GPM
37.8 L/min
Peak Flow Rate**@
30 psi (or less) 12 GPM
45.4 L/min 16.5 GPM
62.5 L/min 15 GPM
56.7 L/min 15 GPM
56.7 L/min 30 GPM
113.5 L/min 30 GPM
113.5 L/min 19 Gpm
71.9 l/min 31 GPM
117.3 L/min 22 GPM
83.2 L/min 15 GPM
56.7 L/min 15 GPM
56.7 L/min 15 GPM
56.7 L/min 15 GPM
56.7 L/min
Resin per tank, In cu. ft. 0.3 0.47 0.4 0.4 0.7 0.7 1.5 2.25 2.25 Upper: 0.4 Resin
Lower: 0.4 Carb Upper: 0.4
ResinLower: 0.4 Upper: 0.25 Carb
Lower: 0.7 Resin Upper: 0.2 Macrolite
Lower: 0.7 Resin
Resin per tank, In litres 8.5 13.3 11.3 11.3 19.8 19.8 42.5 42.5 63.7 Upper: 11.3 Resin
Lower: 11.3 Carb Upper: 11.3 Resin
Lower: 11.3 Carb Upper: 7.0 Carb
Lower: 19.8 Resin Upper: 5.6 Macrolite
Lower: 19.8 Resin
Capacity Per Cycle, In
Grains @ Salt Used Per
Cycle Setting LBS 4693 @ 1.25 7867 @ 1.8*
9802 @ 2.7 5222 @ 1.0* 5222 @ 1.0* 12481 @ 2.7*
15813 @ 4.0 12481 @ 2.7*
15813 @ 4.0 25,253@5.5*
41,087@10.0* 25,253@5.5*
41,087@10.0* 65,139 @ 15*
81,845 @ 30 4921@1.0* 4921@1.0* 13,303 @ 4.0 14,883 @ 4.4
Capacity Per Cycle, In Grams
@ Salt Used
Per Cycle Setting kg 304 @ 0.56 509 @ 0.82*
634 @ 1.2 338 @ 0.455* 338 @ 0.455* 807 @ 1.21*
1023 @ 1.8 807 @ 1.21*
1023 @ 1.8 1634@2.5*
2659@4.5* 1634@2.5*
2659@4.5* 4216 @ 6.8*
5297 @ 13.6 318@4.5* 318@4.5* 745 @ 1.8 809 @ 1.9
Grains Exchanged Per
Pound Of Salt Used 3754 @ 1.25 4371 @ 1.8*
3630 @ 2.7 5222 @ 1.0* 5222 @ 1.0* 4622 @ 2.7*
3953 @ 4.0 4622 @ 2.7*
3953 @ 4.0 4591*@5.5*
4108*@10.0* 4591*@5.5*
4108*@10.0 4342* @ 15.0*
2728 @ 30.0 4921@1.0* 4921@1.0* 3326 @ 1.8 3383 @ 1.9
Grams ExchangedPer kg
Of Salt Used 542 @ 0.56 629 @ 0.82*
523 @ 1.2 752 @ 0.455* 752 @ 0.455* 574 @ 0.82*
546 @ 1.2 574 @ 0.82*
546 @ 1.2 661@2.5*
591@4.5* 661@2.5*
591@4.5* 625 @ 6.8*
393 @ 13.6 708@0.45* 708@0.45* 413.8 @ 0.81 425.7 @ 0.86
Max. Flow Rate to Drain
During Regeneration 2.2 GPM
8.3 L/min 1.6 GPM
6.1 L/min 1.6 GPM
6.1 L/min 1.6 GPM
6.1 L/min 2.2 GPM
8.3 L/min 2.2 GPM
8.3 L/min 3.2GPM
12.1 L/min 3.2GPM
12.1 L/min 5.2 GPM
19.7 L/min 2.7 GPM
10.2 L/min 2.7 GPM
10.2 L/min 2.9 GPM
10.9 L/min 3.4 GPM
12.9 L/min
Min./Max. Operating
Pressure 103.4 - 861.9 kPa
15 to 125 ps 172.3-861.9 kPa,
25-125 psi 103.4-861.9 kPa,
15-125 psi
Min./Max. Operating
Temperature 2 - 49° C
35 - 120° F
Max. Working Pressure
in PSI 861.9 kPa,
125 psi
*Meets California efficiency requirements of 4000 grains exchanged per pound of salt used. Efficency is only certified
at the low salt dosage and was determined in accordance with NSF/ANSI 44.
**Manufacturer’s tested and verified rate- nt certified or verified by NSF or WQA
Sodium Information: Systems using sodium chloride for regeneration will add sodium to the water.
The amount of sodium added is proportionate to the amount of hardness removed. People who are
on sodium-restricted diets should consider the added sodium as part of their overall sodium intake.
Inlet Hardness Sodium Added
171 mg/liter (10 grains) 79 mg/liter
342 mg/liter (20 grains) 149 mg/liter
513 mg/liter (30 grains) 223 mg/liter
1192 mg/liter (40 grains) 298 mg/liter
Kinetico reverse osmosis systems will remove as much as 98 percent of sodium content in the water.
Using potassium chloride as a regenerant will not add sodium to the water.
Kinetico Water Softeners (Mach 2025s, 2030s, 2040s with Overdrive, 2060s, 2060s with
Overdrive, 2100s, 2100s with Overdrive, 2175s, 4040s with Overdrive and 4060s with
Overdrive) are tested and certified by NSF International and/or the WQA against the
requirements of NSF/ANSI Standard 44 for softener performance and chemical reduction of
barium and radium 226/228. The Kinetico 4060s/Macrolite® with Overdrive is tested and
certified by NSF International and/or the WQA against the requirements of NSF/ANSI
Standard 42 for Particulate Reduction Class III, 4060s/Carbon for chlorine reduction and
Standard 44 for softener performance and chemical reduction of barium and radium
226/228. NSF/ANSI International and/or the WQA certifies our product performance and
reviews our manufacturing facility and procedures to assure product consistency and integrity.
They also assure that our literature accurately reflects our product capabilities.
Certified Continuous Flow Rate as validated by NSF International represents continuous
service flow of water at 15 psi pressure drop and is not an indication of maximum flow rate
or unit limitation. U.S. Patents: 4,336,134; 4,579,242; 4,889,623; 4,972,877; 5,022,994;
5,490,932 These products are not intended to be used for treating water that is microbiolog-
ically unsafe or of unknown quality without adequate disinfection before or after the system