background image

POWER PAK II / PLUS II

10

9. Frequently Asked Questions

Q.      How do I turn ON the POWER PAK II?

A.  Press the ON / OFF / TEST Button (1).

Q.      How do I turn OFF the multi-function POWER PAK II?

A.  The POWER PAK II will turn OFF automatically when not in use (approx. 1-2min), or when charging has completed.

Q.      How many times can the POWER PAK II re-charge my mobile phone?

A.  The POWER PAK II can recharge your mobile phone approx. 2 - 3 times for the KP1405 & approx. 2 - 4 times times for 

the KP1406.The quantity of re-charges for mobile devices could vary depending on the product and its battery capacity, 
also how charged the POWER PAK II is at the time.

Q.      How long will the POWER PAK II take to re-charge my mobile phone?

A.   The POWER PAK II can recharge your IPhone 4/5/6/7 mobile phone in approx. 1 hour. Other mobile devices could take 

longer depending on the product and its battery capacity.

Q.      How long will the POWER PAK II take to re-charge my laptop?

A.   The POWER PAK II can recharge a laptop battery to approx. 45-100% in approx. 1 hour depending on the product and its  

battery capacity.

Q.      How many times can the POWER PAK II jump start my vehicle if the battery is fully charged?

A.  The POWER PAK II can deliver approx. 20 starts for KP1405 & approx. 50 starts for KP1406 on a when fully charged but 

varies depending on the vehicles starting power draw requirements. 

Q.      How long will a fully charged POWER PAK II remain charged sitting in my vehicle?

A.  The POWER PAK II can remain up to 80% charge for up to 6-8 months. The internal temperature of your vehicle can 

affect the battery charge time so it is recommended to check or recharge the POWER PAK II every 3-6 months to ensure 
it is in optimal working condition.

10. Resetting The Current Overload

To reset the current overload feature you need to connect the 240V AC Charger (10) to the 15V DC 1A Input Charging Port (6)  
and turn ON the mains power of your power socket. This will reset the current overload feature of your POWER PAK II and  
you can continue using the POWER PAK II. 

11. Troubleshooting

PROBLEM

CAUSES

SOLUTIONS

The 

POWER PAK II

 Battery Charge LED 

Indicators (2) are showing 4 illuminated 

LED’s , but will not start the vehicle or 

charge any device.

During extended periods of non use or 

extreme temperatures the POWER PAK II 

could loose charge of up to 40%, but the 

unit may still indicate full charge.

Recharge the 

POWER PAK II

 using the 

240V AC Charger (10) or 12V DC  

Car Charger (11).

No response when pressing the ON/

OFF/TEST Button (1) of the  

POWER PAK II

.

The low voltage/over current overload 

circuit within the 

POWER PAK II

 has 

initiated.

To reset the low voltage/over current  

connect the 

POWER PAK II

 using the 240V 

AC Charger (10).

The 

POWER PAK II

 is hot to touch when 

charging laptop batteries.

The charging current of the laptop could 

be above the maximum capacity (3.5A)

Disconnect the POWER PAK II and allow 

to cool down first. Please check that the 

laptop charging voltage and current are 

correct. Reconnect the POWER PAK II and 

recharge your laptop battery.

Summary of Contents for KP1405













Reviews: