5
500KG VERTICAL TRANS STAND
Maintaining Oil Level
Important Note:
When adding or replacing oil, always use a good grade Hydraulic Jack Oil. Avoid mixing types of oil. DO NOT use
Brake Fluid, Alcohol, Glycerin, Detergent, Motor Oil or Dirty Oil,mproper fluid can cause serious internal
damage to Hydraulic Cylinder (6).
Adding Oil:
With Hydraulic Ram (2) fully lowered & Transmission Jack on level ground, remove Purge Cap (4). Oil level should be at the
filler hole. If low, add oil until it start to leak back out then close Purge Cap (4).
Replacing Oil:
For better performance & longevity, replace oil supply once a year. To drain oil, open Purge Cap (4) and loosen the Release
Valve (3) by turning counterclockwise. BE VERY CAREFUL not to permit dirt or foreign matter to get into the system. Tilt the
jack until all old oil has drained out, refill with Kincrome Hydraulic Jack Oil (K12400) and reinstall the Purge Cap (4) and wipe
away any spilt fluid. Prime jack before lifting a load.
Priming/Purging Jack
If the Transmission Jack is not lifting as intended or hydraulic fluid replacements has just been completed then the
Transmission Jack needs to be primed/bleed to ensure no air is in the hydraulic system. Remove the Purge Cap (4), undo the
Release Valve (3) and allow the Saddle (1) to lower to the lowest position. Pump the Foot Pedal (7) at least ten times (X10) to
force air from the system. Wipe away any spilled oil and reinstall the Purge Cap (4), tighten the Release Valve (3) and test the
unit.
Cleaning
The Transmission Jack should be wiped clean with soft cloth only. Do not use gasoline, kerosene, or other such solvents or any
abrasive cleanser as cleaning agents and solvents will cause deterioration of the hydraulic seals.
Storage
Before storage, twist Release Valve (3) counterclockwise to release pressure in Hydraulic Cylinder (6). Store jack level, in a
clean environment, preferably indoors, in a dry area to protect jack from moisture.
Repairing Jack
There are no user serviceable parts except as outlined above. Only trained, licensed and certified repair personnel
should attempt any repairs or replacing of parts. Any modifications to the Transmission Jack, except those performed by the
manufacturer, or their designee, will void all warranties both written and implied.
Australian Office Contact Details
UK Office Contact Details
Phone: 1300 657 528
Mail: Kincrome UK Ltd PO Box 646 Eastleigh SO50 ONA
Fax: 1300 556 005
Email: [email protected]
Email: [email protected]
Website: www.kincrome.co.uk
Website: www.kincrome.com.au
WARRANTY
Warranty given by Kincrome Tools & Equipment Pty Ltd of 3 Lakeview Drive, Caribbean Park, Scoresby, Victoria, Australia (Tel
+61 3 9730 7100) If this product has materials or workmanship defects (other than defects caused by abnormal or non warranted
use) you can, at your cost, send the product to place of purchase, an authorised Kincrome service agent or one of Kincromes
addresses for repair or replacement. Your rights under this warranty are in addition to any other rights you have under the
Australian, United Kingdom & Ireland Consumer Law or other applicable laws. Our goods come with guarantees that cannot
be excluded under the Australian, United Kingdom & Ireland Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For further
details please visit www.kincrome.com.au or call us. Due to minor changes in designor manufacture, the product you purchase
may sometimes differ from the one shown on the packaging.
Summary of Contents for K12120
Page 6: ...6 www kincrome com au...
