background image

6

2 PIECE VEHICLE POSITIONING JACKS

50

FAN

CARE & MAINTENANCE

Caution: Prior to making any adjustments ensure the pressure is removed from the hydraulic system.
Caution:

 These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the 

hydraulically operated tool. Lubrication of this product is critical. Any contaminents such as dirt, rust, etc. may damage internal 
components of the hydraulic assembly.  

1.  

BEFORE EACH USE, inspect the general condition of the tool. Check for:

 

a) loose hardware or housing.

 

b) misalignment or binding of moving parts.

 

c) cracked or broken parts.

 

d) any other condition that may affect its safe operation.

2. 

When not in use, store the equipment in a dry location with the vehicle positioning jacks fully retracted with the pressure  

 

released via the pump release valve (4). 

3. 

Periodically check the unit for signs of rust or corrosion.  

 

Clean exposed areas with a clean oiled cloth.

4. 

Check and maintain the hydraulic oil level. Only use high quality Hydraulic Jack oil, such as Kincromes’ K12400 HYDRAULIC  

 

JACK OIL 500ml.

5. 

Lubricate the hydraulic piston, linkage and foot pedal with a light machine oil.

6. 

Lubricate the castors and axles with bearing grease.

7. 

Clean all the surfaces regularly and maintain all labels and warnings on the vehicle positioning jacks. 

8. 

Clean the castors regularly to ensure they are free from dirt etc. before use. Doing so will prevent possible damage. 

Caring For The Environment

When a tool is no longer usable it should not be disposed of with household waste, but in an environmentally friendly way.  
Please recycle where facilities exist. Check with your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution  
in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

Symbol

Property or statement

kg

Weight in kilograms

WARNING marking concerning Risk of Eye Injury. 

Wear ANSI-approved eye protection.
WARNING marking concerning Risk of Hearing Loss.  Wear hearing protection.

WARNING marking concerning, Risk of Respiratory Injury. Wear NIOSH-approved dust mask/respirator.

WARNING or 

Marking concerning/Risk of Injury.

Summary of Contents for K12101











Reviews: