Kikusui KJM6710 Operation Manual Download Page 49

Page: 49 / 60

KJM6710

Maintenance 5-1

Chapter 5

Maintenance

This chapter describes maintenance and inspection of the KJM6710.
Conduct periodic maintenance and inspection to maintain the initial

performance as long as possible.

5.1

Cleaning

If the panel needs cleaning, gently wipe using a soft cloth with water-
diluted neutral detergent.

• Be sure to turn off the power switch before cleaning.
• Do not use volatile solvents such as thinner or ben-

zine. They may discolor the surface or erase the

printed characters.

5.2

Inspection

DC plug:

Check for ruptures in the covering, play or cracks in the

plug and so on.

• Breaks in the insulation coating may cause electric

shock. If a break is found, stop using it immediately.

To purchase accessories, contact your Kikusui agent or distributor.

5.3

Calibration

The KJM6710 is calibrated at the factory before shipment. However,

periodic calibration is necessary due to changes that occur after

extended use.
For calibration, contact your Kikusui agent or distributor.

CAUTION

WARNING

Summary of Contents for KJM6710





























































Search results

Summary of Contents for KJM6710

Reviews:

Kikusui KJM6710, Operation Manual, Page: 49 / 60

Search results

Summary of Contents for KJM6710

Reviews: